Delta DP3400 instruction manual Maintenance, Engine Pump, To Check Oil, How To Change Pump Oil

Page 13

12. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

W

trigger lock (W) when gun is not in use to prevent

 

accidental spraying.

 

13. Adjust spray for the task being performed by changing quick connect nozzle. Refer to Spray Wand Nozzles.

Shutting Down

1.If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly.

Caution: Risk of property damage Failure to do so could cause damage to the pump.

2.Turn engine off. Refer to the engine instruction manual.

Caution: Risk of property damage. Never turn water supply off while pressure washer engine is running or damage to pump will result.

3.Turn water source off.

4.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.Refer to Storage for proper storage procedures.

MAINTENANCE

WARNING: Risk of burning. When performing maintenance, you may be exposed to hot surfaces, water pressure or moving parts that can cause serious injury or death.

WARNING: Risk of fire. Always disconnect, spark plug wire, let the engine cool and release all water pressure before performing any maintenance or repair. The engine contains flammable fuel. Do not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer,

a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high temperatures or dusty conditions, more frequent maintenance checks will be required.

Engine

Consult the engine instruction manual for the man­facturer's recom- mendations for any and all maintenance.

NOTE: The pressure washer frame is equipped with an oil drain hole to help make changing the engine oil easier.

Pump

NOTE: The pump was filled with oil at the factory.

1.Change pump oil after the first 10 hours of operation and every 250 hours thereafter.

To Check Oil

1.The oil level should come to the dot in the middle of the sight glass (X).

How To Change

H

Pump Oil

 

 

1.

Loosen pump dipstick/oil

 

plug (H).

 

X

2.

Place a

container

under

 

the oil drain plug (Y).

3.

Remove

pump oil

drain

 

plug.

 

Y

4.After oil is drained, replace

oil drain plug. Tighten securely.

5.Remove pump dipstick/oil plug and fill with 14 oz. (414 ml) of DP70 pump oil. If DP70 is not available use 30W non-detergent oil.

English

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents DP3400 Pressure Washer Laveuse à pression Lavadora a presión Specifications Pump SpecificationsModel Weight Height Width PSI GPMImportant Safety Instructions Definitions Safety GuidelinesDeWALT What can happen How to prevent it What can happen Never leave wand unattended while unit is running When Transporting or storing Use a tire pressure gauge To these very rapidly. AdjustTo check the tires pressure Before each use and whilePressure Washer Assembly Fig Operation Pressure AdjustmentsSpray Wand Nozzles Fig Starting Chemicals and Cleaning SolventsChanging Nozzles on Spray Wand To apply chemicals and solventsRefer to Chemicals and Cleaning Solvents Start-up ProcedureTurn the water source on How To Change Pump Oil MaintenanceEngine Pump To Check OilTo Remove Tires To Clean the Water Inlet FilterSTORAGE Engine Pump Replace pump dipstick/oil plug and tighten securelyLimited Warranty Accessories Service InformationPressure Washer RepairsEnglish Glossary Problem Code Troubleshooting GuidePossible Solution Troubleshooting CodesCode Possible cause Troubleshooting Codes Fiche technique Caractéristiques techniques de la pompeMoteur General TX1508Directives de sécurité importantes Définitions lignes directrices en Matière de sécuritéConserver CES Directives Ce qui peut se produire Comment l’éviter Se solder par une amputa Et animale, ce qui pourraitDes fuites provoquées par Inspecter périodiquementLe tube ou les raccords du Raccords sont serrés et enTuyau avec le système sous PressionDémarrage correcte pour Suivre la procédure deQui provoquerait ainsi une Au brasAvertissement Risque d’éclatement Avertissement Attention Surfaces Chaudes Pression Fig Assemblage de la laveuse hauteJusqu’à ce que les boutons soient solidement fixes Tion D. S’assurer que les deux pièces sont bien fixéesRéglages de la pression FonctionnementBuses du tube de pulvérisation Fig SationChangement DES Buses SUR LE Tube DE Pulvérisation Produits chimiques et solvants de nettoyageApplication DE Produits Chimiques ET Solvants Procédure DE Démarrage DémarrageNettoyage Chimiques et solvants deReporter à la section Buses du tube de pulvérisation Moteur EntretienPompe Vérification DU Niveau D’HUILERetrait des pneu Nettoyage du filtre de l’admission d’eauRangement Glisser le collet hors de l’essieu et retirer le pneuLaveuse haute pression AccessoiresInformation SUR LES Réparations RéparationsGarantie limitée Glossaire Guide de dépannage Solution ProbableCodes de dépannage Problème CodeCodes de dépannage suite Français Especificaciones Especificaciones de la bombaMotor Instrucciones de seguridad importantes Definiciones Normas de seguridadConserve Estas Instrucciones Graves¿Qué puede suceder? Cómo evitarlo Peligro Riesgo de explosión o incendioDE Líquido y laceración Peligro Riesgo Respiratorio asfixiaLaceración Continuar Peligro Riesgo de operación insegura Observe el flanco para ver la PropiedadNota Los tanques de aire Los compresores y el equipoAdvertencia Riesgo DE superficies calientes Conserve Estas Instrucciones Para Futuras ConsultasAdvertencia Riesgo de quemadura química Ensamblado de la lavadora a presión Fig InstalaciónAjustes a la presión OperaciónBoquillas para la varilla pulverizadora Fig Varilla pulverizadoraPuesta en marcha Productos químicos y solventes de limpiezaCambio DE LAS Boquillas DE LA Varilla Pulverizadora Para Aplicar Productos Químicos Y SolventesProcedimiento DE Puesta EN Marcha Mantenimiento ApagadoAbra la fuente de agua Suelte el disparador para detener el flujo de aguaBomba MotorLimpieza de las boquillas Para Controlar EL AceitePara quitar los neumáticos Para limpiar el filtro de entrada de aguaAlmacenamiento Retírelo tomando el extremo para sacarloAccesorios Lavadora a presiónInformación DE Mantenimiento ReparacionesExcepciones Garantía limitadaPara Otras Localidades Llame AL 55 5326 GlosarioCódigos de detección de problemas Guía de detección de problemasProblema Código Código Causa posibleOperación Códigos de detección de problemas continuar Español MAR06 Form No. A16411 DP3400 Copyright 2005, 2006 DeWALT DeWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD
Top Page Image Contents