Cisco Systems user manual Outline of the CF2001P System Setup

Page 2

CF2001P

NEXT

1. Outline of the CF2001P System Setup

NOTE

•Install and setup each option according to the instructions included with the option.

•For information on adjusting each option, refer to the section “10. Adjusting the Options” on page 29.

When setting up the system consisting of this unit and its options, set up each unit in the order shown below.

NOTE

Set up each unit correctly according to its SETUP INSTRUCTIONS.

1-A. Copy Table CT-2

2-A. Paper Feed Unit PF-118

2-B. Large Capacity Cabinet PF-117

2-C. Copy Desk CD-2M

3-A. Dehumidifying Heater PF-117

3-B. Dehumidifying Heater PF-118

4.CF2001P Printer

5.Duplex Unit AD-14

6.Data Terminal DT-105*1,*2

*1: U.S.A and Canada only

*2: Not available if the MicroPress PrintLink 2020m is installed

 

 

 

7.

Mechanical Counter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8.

I/F Kit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9.

Controller

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10-A. 10-Mailbin Sorter

 

10-B. Finisher FN-107

 

10-C. Finisher FN-108*2

JS-1002*2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C4004U551CA

4004-7715-01

– 1 –

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents CF2001P Outline of the CF2001P System Setup Unpacking the Printer Unpacking the AccessoriesUnpacking Removing the Protective Tape and Packing Materials Installing the Units Installing the Imaging UnitsShaded area, is only attached to Clear plastic protective sheet is notPacking material therefore, do not remove Black imaging unitBe sure to support the upper right-side door Installing the Oil-Coating UnitBe sure to install the imaging units in their correct slots While carefully opening it otherwise, it mayRemove the oil-coating unit from its box Filling the Toner C4004U062AA Affixing the Support Label Connecting the CablesAffix the label that corresponds with the installed options Loading Test Paper Installing the Manual HolderChecking the Operation of the Printer Setting Up the Servicing Equipment CF2001PSetting Up the Converter Setting Up the Selector Connecting the Equipment Cables TorRite Caliblation Click X-Rite Calibration in the Tech. Rep. Mode screen Dialog box appears if the auto-cal strip was read correctly Turn the cyan test pattern to its original ori Dialog box If the cyan test pattern is read correctlyRead the Pattern of Cyan disappears from Making System Setting Checking the Date SettingSpecifying the Serial Number Specifying Who Performs Replacements Printing the List Click Image Processing To set the Energy Save Mode parameter Select the C Clear key to erase the entered numberTo set the Sleep Mode parameter Loading Paper TraySlide the lateral guides against the edges Paper Adjusting the Options Checking the Paper Reference Position for PF-118Click PRT Area Adjusting the Paper Reference Position for PF-118 Click Machine Adjust Click Left Margin Do not measure from the back of the test PatternChecking the Hole-Punching Positions for FN-107 Setting DT-105 USA and Canada only Connecting the Telephone CablesPrecautions for Connecting a Telephone to the Data Terminal Transmission SettingsDate/Time Settings Enter the service representative’s ID code Maintenance Center Billing Center SettingsClearing the Maintenance RAM DT Settings If the number is not 6-digits long, add 0 at the beginningSetting the Telephone Number Return Initial Transmission
Top Page Image Contents