Cisco Systems CF2001P Clear plastic protective sheet is not, Shaded area, is only attached to

Page 6

CF2001P

NEXT

Protective sheet

*

7. Remove the protective tape from the imag- ing unit.

 

 

NOTE

 

 

The clear plastic protective sheet is not

 

 

packing material; therefore, do not remove

 

 

it.

C4004U193AA

 

 

*

The additional protective sheet, indicated by

 

 

 

the shaded area, is only attached to the

 

 

black imaging unit.

 

8.

Keeping the imaging unit level, pick it up by

 

 

supporting it on the bottom with your left

 

 

hand and on the bottom at the front with your

 

 

right hand.

NOTE

Be sure to insert the imaging unit until the end of the bottom imaging unit cover con- tacts the back of the imaging unit compart- ment.

C4004U052AB

NOTE

Do not insert the imaging unit into the com- partment at an angle.

C4004U215AB

NOTE

When holding the imaging unit, be sure to hold it by its bottom cover. If the top imaging unit cover is held, it may fall off or the PC drum installed on the imaging unit may become damaged, resulting in decreased image quality.

C4004U217AB

10.While keeping the bottom of the imaging unit supported with your left hand, carefully insert the imaging unit with your right hand,

as shown, until the cartridge snaps into place.

C4004U216AB

C4004U053AB

9.Keeping the imaging unit level, insert the imaging unit as far as possible into the imag- ing unit compartment.

Insert the imaging unit with the protective sheet(s) attached.

11.Pull out the empty imaging unit cover. The empty imaging unit cover for the black imaging unit can simply be pulled out, even if the protective sheets on the imaging unit become caught on the toner hopper lid.

C4004U051AC

C4004U054AB

4004-7715-01

– 5 –

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents CF2001P Outline of the CF2001P System Setup Unpacking the Accessories UnpackingUnpacking the Printer Removing the Protective Tape and Packing Materials Installing the Units Installing the Imaging UnitsShaded area, is only attached to Clear plastic protective sheet is notPacking material therefore, do not remove Black imaging unitBe sure to support the upper right-side door Installing the Oil-Coating UnitBe sure to install the imaging units in their correct slots While carefully opening it otherwise, it mayRemove the oil-coating unit from its box Filling the Toner C4004U062AA Connecting the Cables Affix the label that corresponds with the installed optionsAffixing the Support Label Installing the Manual Holder Checking the Operation of the PrinterLoading Test Paper Setting Up the Servicing Equipment CF2001PSetting Up the Converter Setting Up the Selector Connecting the Equipment Cables TorRite Caliblation Click X-Rite Calibration in the Tech. Rep. Mode screen Dialog box appears if the auto-cal strip was read correctly Turn the cyan test pattern to its original ori If the cyan test pattern is read correctly Read the Pattern of Cyan disappears fromDialog box Making System Setting Checking the Date SettingSpecifying the Serial Number Specifying Who Performs Replacements Printing the List Click Image Processing To set the Energy Save Mode parameter Select the C Clear key to erase the entered numberTo set the Sleep Mode parameter Loading Paper TraySlide the lateral guides against the edges Paper Adjusting the Options Checking the Paper Reference Position for PF-118Click PRT Area Adjusting the Paper Reference Position for PF-118 Click Machine Adjust Click Left Margin Do not measure from the back of the test PatternChecking the Hole-Punching Positions for FN-107 Setting DT-105 USA and Canada only Connecting the Telephone CablesPrecautions for Connecting a Telephone to the Data Terminal Transmission SettingsDate/Time Settings Maintenance Center Billing Center Settings Clearing the Maintenance RAMEnter the service representative’s ID code DT Settings If the number is not 6-digits long, add 0 at the beginningSetting the Telephone Number Return Initial Transmission
Top Page Image Contents