Cisco Systems CF2001P user manual Unpacking the Printer, Unpacking the Accessories

Page 3

 

 

NEXT

 

 

CF2001P

 

 

 

 

 

 

 

 

2. Unpacking

Unpacking the Printer

Unpacking the Accessories

1. Open the printer box, and then remove the box containing the imaging unit.

1.Remove the accessories from the box, and then check that the following are

enclosed.

 

 

NOTE

 

 

 

 

 

Remove the box containing the imaging unit before removing the box from around

(1)

Imaging units

4

 

the printer.

 

(2)

Power cord *1

1

 

 

 

(3)

LED cleaning tool *2

1

2. Remove the box from around the printer.

(4)

LED cleaning paper *2

1

3.

Remove the printer from the plastic bag.

(5)

Manual holder

1

4.

Open the two handle covers, and then pull out the handles.

(6)

User Manual

1

 

 

 

(7)

Setup Instructions

1

 

 

 

(8)

Warranty card *3

1

 

 

 

(9)

Power cord instruction *1

1

 

 

 

(10)

Paper size label

1

 

 

 

(11)

Cable clamp

1

 

 

 

(12)

Support label

1

 

 

 

(13)

Additional information

 

 

 

 

 

(Storing the LED cleaning tool)

1

 

 

 

*1 For Particular area only.

 

 

 

 

*2 The LED cleaning tool and its paper are not used during setup. Since they will be

 

 

 

needed when the imaging unit is changed or the printer is cleaned, keep them in a

 

 

 

safe place for later use.

 

 

 

C4004U003AA

*3 U.S.A. and Canada only.

 

 

 

5. Grasp the two handles on the right side of

 

 

 

 

 

 

 

 

 

 

the printer and the two grips on the left (as

 

 

 

 

 

shown in the illustration), and then, while

 

 

 

 

 

keeping the printer level, remove it from its

 

 

 

 

 

box.

 

 

 

 

 

NOTE

 

 

 

 

 

The printer weighs about 77 kg (169-3/4

 

 

 

 

C4004U004AA

lbs.). The printer must be lifted by at least

 

 

 

 

two people. When lifting the printer, be care-

 

 

 

 

 

 

 

 

 

 

ful not to strain your back.

 

 

 

 

 

6. Carefully place the printer on a level and

 

 

 

 

 

sturdy surface, such as a table.

4004-7715-01

– 2 –

 

 

 

 

 

 

Image 3
Contents CF2001P Outline of the CF2001P System Setup Unpacking the Accessories UnpackingUnpacking the Printer Removing the Protective Tape and Packing Materials Installing the Imaging Units Installing the UnitsBlack imaging unit Clear plastic protective sheet is notPacking material therefore, do not remove Shaded area, is only attached toWhile carefully opening it otherwise, it may Installing the Oil-Coating UnitBe sure to install the imaging units in their correct slots Be sure to support the upper right-side doorRemove the oil-coating unit from its box Filling the Toner C4004U062AA Connecting the Cables Affix the label that corresponds with the installed optionsAffixing the Support Label Installing the Manual Holder Checking the Operation of the PrinterLoading Test Paper CF2001P Setting Up the Servicing EquipmentSetting Up the Converter Setting Up the Selector Tor Connecting the Equipment CablesRite Caliblation Click X-Rite Calibration in the Tech. Rep. Mode screen Dialog box appears if the auto-cal strip was read correctly Turn the cyan test pattern to its original ori If the cyan test pattern is read correctly Read the Pattern of Cyan disappears fromDialog box Checking the Date Setting Making System SettingSpecifying the Serial Number Specifying Who Performs Replacements Printing the List Click Image Processing Select the C Clear key to erase the entered number To set the Energy Save Mode parameterTo set the Sleep Mode parameter Tray Loading PaperSlide the lateral guides against the edges Paper Checking the Paper Reference Position for PF-118 Adjusting the OptionsClick PRT Area Adjusting the Paper Reference Position for PF-118 Click Machine Adjust Click Left Margin Pattern Do not measure from the back of the testChecking the Hole-Punching Positions for FN-107 Connecting the Telephone Cables Setting DT-105 USA and Canada onlyTransmission Settings Precautions for Connecting a Telephone to the Data TerminalDate/Time Settings Maintenance Center Billing Center Settings Clearing the Maintenance RAMEnter the service representative’s ID code If the number is not 6-digits long, add 0 at the beginning DT SettingsSetting the Telephone Number Initial Transmission Return