Tripp Lite Single-Phase 10kVA owner manual Storage and Service, Warranty and Warranty Registration

Page 15

Storage and Service

Storage

Before storing your UPS, turn it completely OFF. If you store your UPS for an extended period of time, recharge the UPS batteries for 4 to 6 hours once every three months. Note: after you connect the UPS to utility power, it will automatically begin charging its batteries. If you leave your UPS batteries discharged for an extended period of time, they will suffer a permanent loss of capacity.

Service

Your SmartOnline UPS is covered by the 2-year limited warranty period described below. A variety of Extended Warranty and On-Site Service Programs are also available from Tripp Lite. For more information on service, call Tripp Lite Customer Support at (773) 869-1234. Before returning your UPS for service, follow these steps:

1.Review the installation and operation instructions in this manual to ensure that the service problem does not originate from a misreading of the instructions.

2.If the problem continues, do not contact or return the UPS to the dealer. Instead, call Tripp Lite at (773) 869-1233. A service technician will ask for the UPS model number, serial number and purchase date and will attempt to correct the problem over the phone.

3.If the problem requires service, the technician will issue you a Returned Material Authorization (RMA) number, which is required for service. They will also discuss proper packaging and shipping procedures. Any damages (direct, indirect, special, incidental or consequen- tial) to the UPS incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. UPS Systems shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on the outside of the package. If the UPS System is within the 2-year warranty period, enclose a copy of your sales receipt. Return the UPS for service using an insured carrier to the address given to you by the Tripp Lite service technician.

Warranty and Warranty Registration

2-Year Limited Warranty

TRIPP LITE warrants its products including batteries to be free from defects in materials and workmanship for a period of two years from the date of initial purchase. After 90 days from the date of purchase, TRIPP LITE’s obligation under this warranty is limited to replacing parts on such defective products. To obtain service under this warranty, you must call TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.

The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system. The warranties of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

The policy of TRIPP LITE is one of continuous improvement. Specifications are subject to change without notice.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Radio/TV Interference Notice:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment is likely to cause harmful interference in which case users will be required to correct the interference at their own expense. The user must use shielded cables and connectors with this product. Any changes or modifica- tions to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.

15

Image 15
Contents SmartOnline Single-Phase 7.5kVA & 10kVA Important Safety Warnings Mounting Rack Post MountingPost Telecom Mounting Mounting Tower Power Module Front Panel Controls FeaturesBattery Module Power Module Detachable Power Distribution UnitBattery Module Feature Description Features Rear PanelPower Module Feature Description Detachable Power Distribution Unit Feature DescriptionPower on Hardwiring CautionsHardwire the PDU to a Utility Power Source Connect the battery module to the power modulePower OFF optional Optional ConnectionPlug Your Equipment into the PDUs Outlets Contact-Closure Communication Connection UPS Power/Battery Module RemovalRisk of electrical shock High Voltage WarningsOperation Startup Self-TestFailed Self-Test On Battery Alarm Normal OperationOverload Messages Shutdown Messages Bypass MessagesYear Limited Warranty Storage and ServiceWarranty and Warranty Registration ServiceManual del propietario Advertencias de seguridad importantes Montaje Bastidor Montaje de 4 postesMontaje de 2 postes Telecomunicaciones Montaje en torre Controles del panel frontal del módulo de potencia CaracterísticasMódulo de batería Características Panel posterior continuación Descripción de características del módulo de potenciaDescripción de características del módulo de batería Encendido ConexiónPrecauciones del cableado Conecte el módulo de batería al módulo de potenciaConecte sus equipos en el UPS Apagado opcionalConexión opcional continuación Operación de derivación manual módulo de potenciaRemoción del módulo de potencia/batería de la UPS ¡ADVERTENCIA! ¡Alto voltaje! ¡Riesgo de choque eléctrico Advertencias de alto voltajeOperación Auto-prueba de arranqueFallo durante la auto-prueba Alarma On Battery Operación normalMensajes de sobrecarga Mensajes de apagado Mensajes BypassAlmacenamiento y servicio AlmacenamientoServicio Póliza DE Garantía Garantía limitada de 2 añosManuel de lutilisateur Avertissements pour Connexion de lEquipement Consignes de Sécurité ImportantesMontage Baie Montage à 4 supportsMontage à 2 supports Telecom Montage Tour Caractéristiques Commandes de Panneau Avant de Module dAlimentationModule Batterie Caractéristiques Panneau Arrière suite Description des Caractéristiques de Module dAlimentationDescription des Caractéristiques de Module de Batterie Connexion Précautions pour CâblageConnecter le module de batterie Au module dalimentation Connecter votre équipement à lUPS Connexion suiteAlimentation en Marche Alimentation sur Arrêt facultatifConnexion Communication Fermeture de Contact Connexion en Option suiteMise en Garde! Haute tension! Risque de choc électrique Mise en Garde! Haute tension Risque de choc électriqueFonctionnement Autotest de DémarrageEchec de lAutotest Messages de Surcharge Alarme Sur BatterieFonctionnement suite Fonctionnement NormalMessages de Fermeture Messages de BypassEntreposage et Service Garantie Limitée à 2 AnsEntreposage Page 200607001 Manual del propietario Manuel du propriétaire Contactos en módulo de potencia/batería Español Français Introduction Post Mounting Mounting RackConnection Troubleshooting Warranty Registration Year Limited WarrantyManual del propietario Introducción Montaje de 4 postes Montaje BastidorMontaje en bastidor continúa Solución de problemas Condiciones Garantía limitada de 2 añosManuel de lutilisateur Consignes de Sécurité Importantes Conserver ces Instructions Montage à 4 supports Montage BaieMontage Baie suite Dépannage Numéros didentification de conformité aux règlements Garantie limitée à 2 ansÐóêîâîäñòâî ïîëüçîâàòåëÿ Page Ìîíòàæ Ñòåëëàæ Ìîíòàæ Ñòåëëàæ ïðîäîëæåíèå Òåõíè÷åñêîå îáñëóæèâàíèå Ãàðàíòèéíûå îáÿçàòåëüñòâà