Powerware FE/QFE UPS manual Ld The AC Line indicator illuminates see Figure

Page 24

ld The AC LINE indicator illuminates (see Figure 2).

NOTE The AC LINE indicator does not illuminate for FE models with serial numbers 25000 and greater until the UPS ON/OFF switch is turned to the ON position.

AC LINE

READY CHARGING BATTERY

ALARM

 

POWER

 

Figure 2. Front Panel Indicators

nd If you have an external battery cabinet with a DC switch, turn the switch to the ON position.

od Turn the UPS ON/OFF switch to the ON position. After a short startup test, the READY indicator flashes for a few seconds and then remains illuminated. The UPS is ready to supply output power.

NOTE The UPS and external battery cabinets are shipped with the batteries charged. However, batteries may lose some of the charge during shipping and storage. You can use the UPS immediately after unpacking, but it may not provide the full-rated backup time during a power failure. Upon initial startup, the UPS may need to operate for

24 hours before the battery is fully charged and full battery-backup time is available. If the CHARGING indicator is illuminated, operate the UPS for 24 hours to fully charge the battery.

rd For Plug-Receptacle UPSs: Plug the equipment to be protected into the UPS output receptacles.

NOTE For QFE models, use the supplied UPS cord to connect your equipment to the

UPS output receptacles.

For Hardwired UPSs: Turn the bypass switch to the UPS position.

sd Turn on the equipment that is connected to the UPS.

18

Powerware® FERRUPS FE/QFE UPS (500 VA–18 kVA) User’s Guide : Rev A www.powerware.com

Image 24
Contents Powerware Ferrups FE/QFE UPS Page Powerware Ferrups FE/QFE UPS Class a EMC Statements FCC Part ICES-003For Users in Germany Table of Contents Alarm Code Summary Service and Support OptionsIntroduction Identifying Your UPSKVA Models 500 VA-3.1 kVA Models Page Safety Warnings P O R T a N T S a F E T Y I N S T R U C T I O N SN G E R R N I N GSikkerhedsanvisninger U T I O NR E Belangrijke Veiligheidsinstructies V a R S E LV a a R A R S C H U W I N GTarkeita Turvaohjeita G E L E TA R a R O I T U SConsignes de sécurité R OSicherheitswarnungen R N U N GH T U N G „Ò·Ûfl· C›„ÈÛÙ.ÃÁ˜ÒÁÙÈÏÔfi95%ÔÈÂflÙÂUPSÍÔÌÙ‹ÛÂÌÂÒ¸fi Avvisi di sicurezza R I C O L OV E R T E N Z a Viktig Sikkerhetsinformasion T E N Z I O N ER L I G Regulamentos de Segurança R S I K T I GI D a D O V E R T Ê N C I aÏðåäóïðåæäåíèÿ ïî ìåðàì áåçîïàñíîñòè R I G OÎïàñíî ÐåäóïðåæäåíèåAdvertencias de Seguridad ÑòîðîæíîL I G R O V E R T E N C I aSäkerhetsföreskrifter E C a U C I Ó NR a K T I G T UPS Startup Startup for the FE and QFE 500 VA-3.1 kVA UPSLd The AC Line indicator illuminates see Figure Startup for the FE and QFE 4.3-18 kVA UPS Program 7LPHWhere is the Battery Ah value from Table DWHExternal Battery Pack Ah Values 9MEOn/Off Switch Power Cord RS-232 Communication Port RS-232 Communication Port On/Off SwitchSwitch Rear PanelsPanel KVA ModelsFront Panel Indicators OperationIndicator Status Using the Control Panel Changing Operating ModesEntering Passwords Operating ModesDisplaying and Changing Parameters Locking and Unlocking the Control PanelUsing the Configuration Menu Remote Control PanelBattery Test Automatic System TestLogic Test Inverter TestParameters ParametersDC power is turned off UPSVA Limit, parameter LowConfigured for use with your network Switch is in the OFF positionShows -63c Used by your equipmentUPS Shutdown Inverter Logs onExplanation Each part of the system test seeU T I O N Extended Power Outages Page Powerware Software Suite CommunicationCommunication Port Connecting a Terminal or Computer to the RS-232 Port DB-9 to UPS Pinout DB-25 Port Settings Keystroke CommandsAction Key Sequence Entering Commands from a Terminal or Computer CommandsCommand DelayShows a list of terminal/computer commands Command then clears the minimum and maximum valuesPassword UPS restar hortly after power returnsShutdown cancel Cancels a shutdown started with the shutdown commandRemote Monitoring Remote ShutdownPage Options Page Maintenance Page Specifications FE and QFE 4.3-18 kVA Audible Noise dB Runtime minutes Full Load Half Load Weight F9E uWA G9E uWA IuWAE9I I9G 103A 149AElectrical Input and Output Environmental and Safety BatteryPage Troubleshooting AlarmsAlarms To start the user test alarm from Alarm offPossible microprocessor problem Temperature probe is missing orAlarm and Inverter Logs Reading the Alarm Log from a Control PanelRequires service Representative UPS off and contact your serviceReading the Inverter Log from a Control Panel Reading the Alarm Log from a Terminal or Computer Inverter CodesAlarm Code Summary Low BatteryReading the Inverter Log from a Terminal or Computer Low AC OutputService and Support 852--3030