Powerware FE/QFE UPS manual Entering Passwords, Operating Modes

Page 34

Table 3. Operating Modes

n l

g r h

v h l

 

 

 

Off

Press [CTRL]-[1]

The UPS does not provide power to your equipment, but you can still use the

 

[ENTER] [ENTER].

control panel if battery power is present. The READY indicator is off.

 

 

 

Auto

Press [CTRL]-[2]

This is the normal operating mode. The UPS conditions AC input power and

 

[ENTER] [ENTER].

provides the conditioned power to your equipment. The UPS is ready to switch

 

 

to battery power if necessary. The AC LINE and READY indicators are

 

 

illuminated.

 

 

 

Line Condition

Press [CTRL]-[3]

The UPS is conditioning AC input power and providing the conditioned power

 

[ENTER] [ENTER].

to your equipment, but if there is a brownout or power outage, the UPS does

 

 

not switch to battery power. Instead, the UPS shuts down its output until AC

 

 

input power is available again. The READY indicator is off when the UPS is in

 

 

this mode.

 

 

 

Inverter On

Press [CTRL]-[4]

The UPS converts battery power to AC power for your equipment. It does not

(Battery Power)

[ENTER] [ENTER].

charge the batteries. The BATTERY POWER indicator is on. The UPS calculates

 

 

the runtime remaining and sounds an alarm when runtime starts to get low.

 

 

 

Entering Passwords

Before you can change some parameter values, you must enter a password. You must also enter a password before you enter some of the commands listed on page 44.

NOTE Some parameters, such as Time, Date, and User ID, are not password-protected initially. If you change parameter 39 to “Yes,” a User password is required to change these parameters, use [CTRL] keys, or use some commands. See “Parameters” on page 32 and “Entering Commands from a Terminal or Computer” on page 44 for more information.

The User Password is 377. If you need a higher password, call your service representative. To enter the User Password, follow these steps:

Press this key:

Display shows:

 

[CLEAR]

)(55836

 

[PROGRAM]

3DVVZRUG￿

 

[3] [7] [7]

3DVVZRUG￿

￿￿￿

[ENTER]

/HYHO￿

8VHU

To clear the password, press [CLEAR] until 3DVVZRUG &OHDUHG appears on the control panel display.

28

Powerware® FERRUPS FE/QFE UPS (500 VA–18 kVA) User’s Guide : Rev A www.powerware.com

Image 34
Contents Powerware Ferrups FE/QFE UPS Page Powerware Ferrups FE/QFE UPS FCC Part ICES-003 Class a EMC StatementsFor Users in Germany Table of Contents Alarm Code Summary Service and Support OptionsIdentifying Your UPS IntroductionKVA Models 500 VA-3.1 kVA Models Page N G E R Safety WarningsP O R T a N T S a F E T Y I N S T R U C T I O N S R N I N GU T I O N SikkerhedsanvisningerR E V a a R Belangrijke VeiligheidsinstructiesV a R S E L A R S C H U W I N GA R a Tarkeita TurvaohjeitaG E L E T R O I T U SConsignes de sécurité R OR N U N G SicherheitswarnungenH T U N G „Ò·Ûfl· C›„ÈÛÙ.ÃÁ˜ÒÁÙÈÏÔfi95%ÔÈÂflÙÂUPSÍÔÌÙ‹ÛÂÌÂÒ¸fi R I C O L O Avvisi di sicurezzaV E R T E N Z a T E N Z I O N E Viktig SikkerhetsinformasionR L I G I D a D O Regulamentos de SegurançaR S I K T I G V E R T Ê N C I aÎïàñíî Ïðåäóïðåæäåíèÿ ïî ìåðàì áåçîïàñíîñòèR I G O ÐåäóïðåæäåíèåL I G R O Advertencias de SeguridadÑòîðîæíî V E R T E N C I aE C a U C I Ó N SäkerhetsföreskrifterR a K T I G T UPS Startup Startup for the FE and QFE 500 VA-3.1 kVA UPSLd The AC Line indicator illuminates see Figure Startup for the FE and QFE 4.3-18 kVA UPS Program 7LPHWhere is the Battery Ah value from Table DWHExternal Battery Pack Ah Values 9MESwitch On/Off Switch Power Cord RS-232 Communication PortRS-232 Communication Port On/Off Switch Rear PanelsPanel KVA ModelsFront Panel Indicators OperationIndicator Status Using the Control Panel Changing Operating ModesEntering Passwords Operating ModesDisplaying and Changing Parameters Locking and Unlocking the Control PanelUsing the Configuration Menu Remote Control PanelLogic Test Battery TestAutomatic System Test Inverter TestParameters ParametersVA Limit, parameter DC power is turned offUPS LowShows -63c Configured for use with your networkSwitch is in the OFF position Used by your equipmentExplanation UPS ShutdownInverter Logs on Each part of the system test seeU T I O N Extended Power Outages Page Powerware Software Suite CommunicationCommunication Port Connecting a Terminal or Computer to the RS-232 Port DB-9 to UPS Pinout Keystroke Commands DB-25 Port SettingsAction Key Sequence Entering Commands from a Terminal or Computer CommandsShows a list of terminal/computer commands CommandDelay Command then clears the minimum and maximum valuesShutdown cancel PasswordUPS restar hortly after power returns Cancels a shutdown started with the shutdown commandRemote Monitoring Remote ShutdownPage Options Page Maintenance Page Specifications FE and QFE 4.3-18 kVA E9I I9G Audible Noise dB Runtime minutes Full Load Half Load WeightF9E uWA G9E uWA IuWA 103A 149AElectrical Input and Output Environmental and Safety BatteryPage Troubleshooting AlarmsAlarms Possible microprocessor problem To start the user test alarm fromAlarm off Temperature probe is missing orRequires service Representative Alarm and Inverter LogsReading the Alarm Log from a Control Panel UPS off and contact your serviceReading the Inverter Log from a Control Panel Reading the Alarm Log from a Terminal or Computer Inverter CodesReading the Inverter Log from a Terminal or Computer Alarm Code SummaryLow Battery Low AC OutputService and Support 852--3030