Lucent Technologies 3000 VA manual Select LAN Configuration

Page 59

Communication 5

A > ASCII Terminal The UPS displays the formatted data on the attached video terminal

B > VT100 Terminal The UPS displays the formatted data on the attached video terminal

P > Printer Dump The UPS prints the formatted data on the attached printer

L > LAN Configuration allows you to configure the UPS for a new LAN mode and displays the Select LAN Configuration Menu

	SELECT LAN CONFIGURATION
1	>	NOVELL
2	>	AS400
3	>	3-COM/LAN MANAGER
4	>	CUSTOM CONFIGURATION
Q	>	TO QUIT THIS MENU

ENTER SELECTION >+>

Select the AS400 option if you are using monitoring software to monitor the UPS

The Custom Configuration option has two screens: the first screen has options available for inverter shutdown, and the second screen has options available for the contact configuration Consult your shutdown software documentation for details on the required signal states for configuring LAN communications

SELECT CUSTOM LAN CONFIGURATION

Instructions: Choose the desired inverter shutdown function.

Warning: It is recommended that this feature should not be used with normal RS-232 communications, conflicts may occur.

A> Inverter shutdown control is enabled active HIGH (+12V)

B> Inverter shutdown control is enabled active LOW (±12V)

C> Inverter shutdown control is disabled

Q> TO QUIT THIS MENU

ENTER SELECTION >=>

#" ! " ! # 6$5$ I!!#

49

Image 59

Contents ##*&% % *& %+# +%* !%&# +*# &, -*$ Page Page Special Symbols UPS UPS with BDM InstallationQuick Start UPS with BIM Installation Quick Start Able of Contents Troubleshooting Model 3000 UPS NtroductionLoad Requirements UPS Model and Battery ConfigurationsBattery Times for the UPS with BDM Battery Times for the UPS and BIMIntroduction Afety Warnings This Manual Contains Important Safety InstructionsSikkerhedsanvisninger Belangrijke Veiligheidsinstructies Tärkeitä turvaohjeita Consignes de Sécurité Safety Warnings Wichtige Sicherheitsanweisungen Importanti istruzioni di sicurezza Safety Warnings Viktig Sikkerhetsinformasion Regulamentos de Segurança Afety Warnings Requisitos de seguridadAfet3 Warnings Viktig säkerhetsinformation Safety Warnings Safety Warnings Unpacking and Inspection UPS and Battery Module StorageImportant Installation Notes Read Before Installing the UPS NstallationSystems That Require a Serial Interface UPS with Bypass Module InstallationSystems That Require Contact Closure UPS with Distribution Module Setup UPS with Isolation Module Setup For Stability Repo UPS with BIM Rear Panel Installation UPS with Hardwired Bypass Module Rear Panel Hz Hardwired BIM Terminal Block Repo Installation Mounting Holes UPS with Bypass Module Startup Phase 200/208/220/230/240VOutput Voltage Indicators Troubleshooting Tips Installation UPS Front Panel S!!! O!!P!!E!!R!!A!!T!!I!!O!!NOperating Modes Normal ModeBattery Mode Bypass ModeBattery Start DiagnosticsBattery Test on Demand Changing the Output Voltage Using the Bypass ModuleUsing Maintenance Bypass UPS ShutdownUPS with Bypass Module Rear Panel 6%Hz BDM Shown 604Hz BDM 240 Output Voltage Indicators Ommunication Initial Communications SettingsOptions Front Panel ommuncatons AccessUPS Serial Communications Menu Ascii Select LAN Configuration Select Baud Rate Serial Port Location UPS Communications Interface PortPWR.FAIL Communications Mode Reference ChartPecifications UPS Model 3000 SpecificationsUPS Physical Specifications Model 3000 Specifications with the 50Hz BIM Model 3000 Specifications with the 60Hz BDMEMC UPS Technical Specifications# ! ! # 6$5$ I!!# Roubleshooting Troubleshooting Service and Support Resetting the UPSSilencing the Alarm PDM06 Parts ListNdex Numeric LOWBATT,49 Over temperature,alarm,58 UTILFAIL,49 EC Declaration of Conformity FCC StatementClass a European EMC Statement