Liebert Series 600T manual Description Location Function, Shutdown Procedures

Page 32

Figure 10 Series 600T UPS and SCC Operator Control Panels

Item

Description (Location)

Function

1

Display Screen

This screen displays all vital UPS information in one convenient location. All of the UPS

 

(SCC and modules)

monitoring functions and conditions are indicated here.

2

Up

This touch-sensitive pad (button) is used to move the cursor up through various

 

(SCC and modules)

selections present on the display screen. Note that all pads on this control panel have

 

 

touch-sensitive switches behind them.

3

Down

Similar to the Up pad, this pad is used to move the cursor down through the various

 

(SCC and modules)

selections present on the display screen.

4

Select

After choosing the desired item (with highlighted cursor) from the display screen with

 

(SCC and modules)

the Up and Down pads, pushing this pad tells the microprocessor to go to the

 

 

highlighted selection.

5

Alarm Reset

This pad is used to clear all of the alarm conditions that are no longer present.

 

(SCC and modules)

However, all active alarms remain in memory and on the applicable screens until they

 

 

are corrected. This pad also resets the History Status Report memory buffer when held

 

 

until the screen clears.

6

Voltage Adjust

This push-to-turn knob permits adjustment of the UPS output voltage to meet load

 

(SCC only)

requirements or to match the bypass voltage before transferring the load to or from

 

 

bypass.

7

UPS

This pad activates the circuits that connect the UPS to the critical load (a retransfer).

 

(SCC only)

When this pad is pushed (along with Control Enable), the UPS output circuit breaker

 

 

closes and the bypass circuit breaker opens.

8

Bypass

This pad activates the circuits that connect the bypass line to the critical load (a

 

(SCC only)

transfer). When this button is pushed (along with Control Enable), the bypass circuit

 

 

breaker closes and the UPS output circuit breaker opens.

9

Control Enable

This pad must be pressed simultaneously with the UPS, Bypass, Battery Trip, or Output

 

(SCC and modules)

Trip pads to activate them.

10

Horn Off

This pad is used to silence the alarm horn after it is activated. When this switch is

 

(SCC only)

pressed, the alarm horn is silenced but the active and latched alarm messages remain

 

 

on the screen. The alarm messages still displayed stop flashing to indicate they have

 

 

been acknowledged.

11

Alarm Horn and

This electronic horn sounds to alert nearby personnel whenever a new alarm occurs. A

 

Red LED (SCC only)

red LED (light emitting diode) is located in the middle of the alarm horn.

12

Emergency Module

During an emergency, pressing this guarded switch will transfer the load to bypass and

 

Off (SCC only)

then shut down the UPS modules. The load will remain on bypass power. (Refer to

 

 

3.3.3 - Shutdown Procedures.)

13

Battery Trip

This pad can be used (along with Control Enable) to trip the module battery disconnect

 

(modules only)

(MBD) circuit breaker open (disconnecting the battery from the UPS module).

14

Output Trip

This pad can be used (along with Control Enable) to trip the module output circuit

 

(modules only)

breaker open (disconnecting the module from the UPS system).

26

Operation

DISCONTINUED

 

 

PRODUCT

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Series 600T UPS DIS Product Table of Contents Manual Procedures Figures Tables Important Safety Instructions Overview of this Manual System Description Multi-Module UPS, 65-80 kVA left and 100-500 kVA rightProduct Multi-Module 500-750 kVA UPS Types of System Control Cabinets SCCs System Control Cabinets SCCsOther Factors to Consider ReliabilityDesigned for Success Safety Precautions Modes of Operation Operator Controls DIS Product Options General Component Descriptions System Control CabinetBattery Plant UPS ModuleDetailed Component Descriptions Controls HardwareFirmware Rectifier/ChargerInput Power Factor Battery Charging CircuitInput Circuit Breaker Isolation TransformerBattery Disconnect Battery Charge Current LimitingBattery Equalize Charge Circuit Operation After End-of-DischargeNon-Linear Load Characteristics Unbalanced Load CharacteristicsInverter Output Regulation and Overload PerformanceStatic Switch Isolation Static BypassFuse Protection Shorted SCR MonitoringPulsed Parallel Operation Load TransfersTransfer and Retransfer Conditions Automatic Transfers to BypassManual Transfers Transfer InhibitedRetransfer Inhibited Redundant ModeManual Retransfers Features Display Screen and Operator ControlsDescription Function System Control Cabinet Operator Controls Sccb Pictured Shutdown Procedures Description Location FunctionSwitches Behind SCC Control Panel Door Menu Tree Master Menu Screen WALK-IN Display modules onlyCustomer Alarm Definitions SCC only Load Transfer Procedures SCC onlyBattery Time modules only Output Metering Displays Monitor/Mimic Display ScreenInput Metering Displays Status/Alarm Message Areas Item 7 Alarm MessagesItem 5 Module Status Messages Item 6 System Status MessagesModule Monitor/Mimic Display Screen Alarm Messages Item 5 Alarm MessagesMOD 1 on Line MOD 2 on Line MOD 3 on Line UPS Ratings UPS Input PWR UPS Ratings UPS Input PWR Bypass Input Load Bypass Input C-A Walk-In Display Screen Walk-In Display Screen During Start-UpStatus Reports Screens Status Reports ScreenPresent Status Select ExitEvent History Event History MODULE-0History Status History Status Report ScreensSCC ModuleBattery Cycle Monitor Module Only System StatusBattery Cycle Monitoring Summary Screen System Configuration Screens System ConfigurationDate Date ScreenTime Time ScreenAuto Dial DialModem Baud Rate Modem Baud RateMaximum Auto-Retransfer Attempts Retransfer AttemptsRemote Monitor Alarm Limit Settings Screen Alarm SettingsProduct Load Transfer Procedures Screen Refer to 3.3.2 Load Transfer Procedures for more detailsStart-Up Procedures Screen Refer to 3.3.1 Start-Up Procedure for more detailsModule Start- Up Procedures Screen Shutdown Procedures Screen Shutdown ProceduresModule Shutdown Procedures Screen Battery Time Screen Module Only VDCBattery Time Screen Example 45 Minute Discharge Range of Values for Calculated Battery Times Aining Rem Tim Calculated La p s e d T im e M in u te sMeter Calibration Screen UP Cursor UP Down Cursor Down Select ChooseBattery Equalize Screen Battery Equalize RechargingAlarm and Status Messages Module Status Messages 3 Modules ConnectedSystem Status Messages Load Block MessagesAbbreviations Used in Alarm Messages OF/UFDC Ground Fault Battery CB OpenPower BatteryManual Reset Static SwitchBypass Phase Control PowerAlarm Indications and Other Alarms That Activate Summary AlarmsSystem Configuration Screens or the watchdog timer has Reverse PowerTemperature Over-TemperatureTimeout System Configuration Screens Load On UPSAlarm Message Special FunctionsCommunication Interfaces Worldwide ReportingAuto-Dial Requesting InformationLocal Reporting to a Terminal Local Reporting to a MonitorSite Reporting SiteScan or Snmp Remote Monitor PanelSeparate / Simultaneous Outputs Load On Bypass ScctOK To Transfer Load on Bypass UPS AvailableLoad on UPS Bypass Available Momentary Overloads Refer to 3.4 Automatic OperationsInput Power Failure Load On Battery Input Power Fail Load on BatteryOne Module Off-Line One Module Off-Line Load on UPSOff Battery Load on UPS Battery Not AvailableRefer to 3.3.3 Shutdown Procedures Emergency Modules OffEmergency Power Off Emergency Power OffRefer to 3.2.10 Maintenance Bypass System ShutdownLoad on Maintenance Bypass Two Breakers Load on Maintenance Bypass Three Breakers Manual Procedures Refer to 3.4 Automatic Operations for more detailsStart-Up Procedure SCC Start-Up B2. Set the Static Switch Disconnects OFF open SCC Start-Up Procedures Screen UPS Module Start-Up Module Start-Up Procedures Screen Product Load Transfer Procedures Maintenance Bypass Load Transfers Maintenance BypassIf the load is on Maintenance Bypass System BypassShutdown Procedures System Shutdown Procedure UPS bypass line is still energized100 Module Shutdown Procedure Remote Emergency Power Off Repo Local Emergency Modules Off LemoAutomatic Operations Overloads Without TransferAutomatic Transfers to Bypass Automatic Retransfers to UPSAutomatic Module Off-Line Automatic Emergency Modules OffMaintenance DIS Product Liebert Global Services Maintenance Agreements The Signature ProgramProfessional Start-Up TrainingAir Filters Routine MaintenanceRecord Log Battery Maintenance Battery Safety PrecautionsDIS Product 112 DIS Product Matching Battery Cabinets Optional Power BatteriesRack-Mounted Batteries Torque RequirementsTorque Specifications Unless Otherwise Labeled Detection of TroubleRecommended Test Equipment Reporting a ProblemCorrective Actions Rating Environmental Conditions Adjustments Battery OperationElectrical Specifications Voltage Adjustment Range Phase BalancingVoltage Transient Recovery Time Voltage Harmonic ContentSeries 600T UPS
Related manuals
Manual 84 pages 39.26 Kb
Top Page Image Contents