Motorola TMS320C6711D warranty PLL Clock Frequency Ranges†‡, GDPA−167, ZDPA-167, Clock Signal

Page 48

SPRS292A − OCTOBER 2005 − REVISED NOVEMBER 2005

PLL and PLL controller (continued)

Table 28. PLL Clock Frequency Ranges†‡

 

 

GDPA−167, ZDPA-167

 

CLOCK SIGNAL

 

GDP-200, ZDP−200

UNIT

 

 

 

 

MIN

 

MAX

 

 

 

 

 

 

PLLREF (PLLEN = 1)

12

 

100

MHz

 

 

 

 

 

PLLOUT

140

 

600

MHz

 

 

 

 

 

SYSCLK1

−

 

Device Speed (DSP Core)

MHz

 

 

 

 

 

SYSCLK3 (EKSRC = 0)

−

 

100

MHz

†SYSCLK2 rate must be exactly half of SYSCLK1.

‡Also see the electrical specification (timing requirements and switching characteristics parameters) in the Input and Output Clocks section of this data sheet.

The EMIF itself may be clocked by an external reference clock via the ECLKIN pin or can be generated on-chip as SYSCLK3. SYSCLK3 is derived from divider D3 off of PLLOUT (see Figure 8, PLL and Clock Generator Logic). The EMIF clock selection is programmable via the EKSRC bit in the DEVCFG register.

The settings for the PLL multiplier and each of the dividers in the clock generation block may be reconfigured via software at run time. If either the input to the PLL changes due to D0, CLKMODE0, or CLKIN, or if the PLL multiplier is changed, then software must enter bypass first and stay in bypass until the PLL has had enough time to lock (see electrical specifications). For the programming procedure, see the TMS320C6000 DSP Software-ProgrammablePhase-Locked Loop (PLL) Controller Reference Guide (literature number SPRU233).

SYSCLK2 is the internal clock source for peripheral bus control. SYSCLK2 (Divider D2) must be programmed to be half of the SYSCLK1 rate. For example, if D1 is configured to divide-by-2 mode (/2), then D2 must be programmed to divide-by-4 mode (/4). SYSCLK2 is also tied directly to CLKOUT2 pin (see Figure 8).

During the programming transition of Divider D1 and Divider D2 (resulting in SYSCLK1 and SYSCLK2 output clocks, see Figure 8), the order of programming the PLLDIV1 and PLLDIV2 registers must be observed to ensure that SYSCLK2 always runs at half the SYSCLK1 rate or slower. For example, if the divider ratios of D1 and D2 are to be changed from /1, /2 (respectively) to /5, /10 (respectively) then, the PLLDIV2 register must be programmed before the PLLDIV1 register. The transition ratios become /1, /2; /1, /10; and then /5, /10. If the divider ratios of D1 and D2 are to be changed from /3, /6 to /1, /2 then, the PLLDIV1 register must be programmed before the PLLDIV2 register. The transition ratios, for this case, become /3, /6; /1, /6; and then /1, /2. The final SYSCLK2 rate must be exactly half of the SYSCLK1 rate.

Note that Divider D1 and Divider D2 must always be enabled (i.e., D1EN and D2EN bits are set to “1” in the PLLDIV1 and PLLDIV2 registers).

The PLL Controller registers should be modified only by the CPU or via emulation. The HPI should not be used to directly access the PLL Controller registers.

For detailed information on the clock generator (PLL Controller registers) and their associated software bit descriptions, see Table 29 through Table 32.

48

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

Page 47 Page 49
Image 48
Page 47 Page 49
Contents SPRS292A − October 2005 − Revised November Table of Contents Revision History Pages ADDITIONS/CHANGES/DELETIONSMultichannel Buffered Serial Port Timing GDP and ZDP BGA packages bottom view GDP and ZDP 272-PIN Ball Grid Array BGA PACKAGES†Bottom View Description Device characteristics Characteristics of the C6711D ProcessorHardware Features Internal Clock C6711DDevice compatibility Functional block and CPU DSP core diagram Digital Signal ProcessorCPU DSP core description ST1 DA1DA2 ST2Memory map summary TMS320C6711D Memory Map SummaryMemory Block Description Block Size Bytes HEX Address Range Peripheral register descriptions Emif RegistersL2 Cache Registers HEX Address Range Acronym Register NameInterrupt Selector Registers Device RegistersEdma Parameter RAM† HEX Address Range Acronym Register Name CommentsEdma Registers Quick DMA Qdma and Pseudo Registers†PLL Controller Registers Gpio RegistersHPI Registers Timer 0 and Timer 1 Registers HEX Address Range Acronym Register Name Comments TimerMcBSP0 and McBSP1 Registers McBSP0 McBSP1Signal groups description CE3 CE2CE1 CE0Gpio GP7EXTINT7 GP6EXTINT6 GP5EXTINT5 GP4EXTINT4CLKOUT2/GP2 General-Purpose Input/Output Gpio PortDevice Configurations Device configurations at device resetConfiguration GDP/ZDP Functional Description PIN BOOTMODE‡CLKMODE0 Devcfg register description EksrcBIT # Name Description Terminal Functions PIN Signal Terminal FunctionsIPD Description Name GDP IPU‡ ZDP Resets and Interrupts IPD Description Name GDP IPU‡ ZDP Jtag EmulationIPD Description Name GDP IPU‡ ZDP HOST-PORT Interface HPI Used for transfer of data, address, and controlLittle Endian HD12Only one asserted during any external data access Decoded from the two lowest bits of the internal addressEmif − ASYNCHRONOUS/SYNCHRONOUS Memory Control ¶ IPD Description Name GDP IPU‡ ZDP Emif − Address ¶ EA9 EA8 EA7 EA6 EA5 EA4 EA3 EA2IPD Description Name GDP IPU‡ ZDP Emif − Data ¶ Multichannel Buffered Serial Port 1 McBSP1Multichannel Buffered Serial Port 0 McBSP0 GENERAL-PURPOSE INPUT/OUTPUT Gpio ModuleRSV RSV IPURSV IPD Name GDP ZDP Supply Voltage Pins DvddCvdd Supply voltage See NoteDescription Name GDP ZDP Supply Voltage Pins Ground PinsVSS GNDPIN Signal TYPE† Description Name GDP ZDP Ground Pins VSSDescription Name GDP ZDP Ground Pins VSS GNDDevelopment support Software Development ToolsHardware Development Tools Device support Device and development-support tool nomenclatureFully qualified production device Device Family Temperature Range Default 0 C to 90 C PrefixDevice Speed Range TechnologyDocumentation support CPU CSR register description Revision IDPwrd PCC DCC Pgie GIECPU CSR Register Bit Field Description CPU IDPCC Cache configuration Ccfg register description Ccfg Register Bit Field DescriptionL2MODE DSP Interrupt Default Selector Module Control Interrupt sources and interrupt selectorDSP Interrupts Interrupt Selector EventEdma module and Edma selector Edma ChannelsEdma Selector ESEL1 Register 0x01A0 FF04 ESEL3 Register 0x01A0 FF0CPLL and PLL controller PLL Lock and Reset Times Clkout Signals, Default Settings, and ControlEnabled or Disabled MIN TYP MAX UnitClock Signal PLL Clock Frequency Ranges†‡GDPA−167, ZDPA-167 Pllcsr Register 0x01B7 C100 PLL Control/Status Register PllcsrPllm Register 0x01B7 C110 PLL Multiplier Control Register PllmDxEN OSCDIV1 Register 0x01B7 C124 Oscillator Divider 1 Register OSCDIV1OD1EN General-purpose input/output Gpio GP7 GP6 GP5 GP4 GP2DIR Power-down mode logic Pwrd Field of the CSR Register PD3 PD2 PD1Power-supply sequencing Characteristics of the Power-Down ModesSystem-level design considerations ModePower-supply decoupling Power-supply design considerationsDvdd DSP Cvdd VSS GNDIeee 1149.1 Jtag compatibility statement Emif device speed Example Boards and Maximum Emif SpeedEmif big endian mode correctness Emif Data Lines Pins Where Data PresentED3124 BE3 ED2316 BE2 ED158 BE1 ED70 BE0 Bootmode ResetRecommended operating conditions‡ MIN NOM MAX UnitIOH Parameter Test Conditions MIN TYP MAX Unit IOZSignal transition levels Parameter Measurement InformationTester Pin Electronics Output Under TestAC transient rise/fall time specifications = 0.3 tcmax† VIL max VUS max GroundTiming parameters and board routing analysis Control Signals † Output from DSP Board-Level Timings Example see FigureOutput from DSP PLL Mode Bypass Mode Unit Input and Output ClocksTiming requirements for Clkin †‡§ See FigureGDPA-167 ParameterClkin CLKOUT3 Timing requirements for ECLKIN† see Figure GDPA-167 ZDPA−167−200 −250Asynchronous Memory Timing Timing requirements for asynchronous memory cycles†‡§See −Figure AreSetup = Strobe = Not Ready CEx BE30 EA212 Address ED310 Read DataAOE/SDRAS/SSOE † AWE/SDWE/SSWE † ArdySetup = Strobe = Not Ready Hold = CEx BE30 EA212AOE/SDRAS/SSOE † ARE/SDCAS/SSADS † AWE/SDWE/SSWE † Ardy SYNCHRONOUS-BURST Memory Timing Timing requirements for synchronous-burst Sram cycles†CEx BE30 BE1 BE2 BE3 BE4EA212 ED310 ARE/SDCAS/SSADS† AOE/SDRAS/SSOE† AWE/SDWE/SSWE†Synchronous Dram Timing Timing requirements for synchronous Dram cycles† see FigureRead Eclkout EA2113 Bank EA112 Column EA12 ED310AOE/SDRAS/SSOE † ARE/SDCAS/SSADS† AWE/SDWE/SSWE† Write Eclkout EA2113EA12 ED310 AOE/SDRAS/SSOE † ARE/SDCAS/SSADS † AWE/SDWE/SSWE †Actv Eclkout CEx BE30 EA2113 Bank Activate EA112 Row Address EA12 ED310AOE/SDRAS/SSOE† ARE/SDCAS/SSADS† AWE/SDWE/SSWE† Dcab EclkoutDeac Eclkout CEx BE30 EA2113 Bank EA112 EA12 ED310Refr Eclkout CEx BE30 EA212 EA12 ED310MRS Eclkout CEx BE30 EA212 MRS value ED310HOLD/HOLDA Timing Timing requirements for See Figure HOLD/HOLDA cycles†Hold Holda Busreq Timing Eclkout BusreqReset Timing Timing requirements for reset†‡ see FigureCLKMODE0 = Phase Clkin Eclkin ResetEmif Z Group† Emif Low Group† Group 2† Boot and Device External Interrupt Timing Timing requirements for external interrupts† see FigureEXTINT, NMI HOST-PORT Interface Timing GDPA−167Hstrobe Hstrobe HrdyHCS Hrdy Has HR/W Hhwil Hstrobe † HCSHas † HR/W Hhwil Hstrobe ‡ HCSHD150 input 1st halfword 2nd halfword HrdyHD150 input 1st half-word 2nd half-word −1 ¶ Multichannel Buffered Serial Port Timing Clks Clkr FSR intBitn-1 ClkxTiming requirements for FSR when Gsync = 1 see Figure ClksFSR external CLKR/X no need to resync CLKR/X needs resync Master Slave MIN MAXMASTER§ Slave MIN Clkx FSXBit Bitn-1 MASTER§ Slave MIN MAX GDPA-167 McBSP Timing as SPI Master or Slave Clkstp = 10b, Clkxp = McBSP Timing as SPI Master or Slave Clkstp = 11b, Clkxp = Timer Timing Timing requirements for timer inputs†TINPx TOUTx GENERAL-PURPOSE INPUT/OUTPUT Gpio Port Timing Timing requirements for Gpio inputs†‡GPIx GPOx DTCKL-TDOV Delay time, TCK low to TDO valid Jtag TEST-PORT TimingTiming requirements for Jtag test port see Figure TCK TDO TDI/TMS/TRSTPackage thermal resistance characteristics Thermal resistance characteristics S-PBGA package for GDPThermal resistance characteristics S-PBGA package for ZDP Mechanical DataOrderable Device Status Package Pins Package Eco Plan Packaging InformationMSL Peak Temp QtyGDP S-PBGA-N272 Seating Plane 4204396/A 04/02ZDP S-PBGA-N272 Seating Plane 4204398/A 04/02Important Notice
Top Page Image Contents