Section 1
General Information
Title | P# | Parameter |
| Description | |
|
|
|
|
| |
Parameters | 86 | Auto Config 2 (for 2nd param set) |
| Definition (Preset Value) | |
Continued |
| Auto configuration flags for the second | Bit0= | Unused | |
|
| parameter set. | Bit1= | Auto 3MC (1, enable auto removal of low voltage ramp for | |
|
|
|
| high start pedestals) | |
|
|
| Bit2= | Auto Bypass (1, enable automatic bypass contactor detection). | |
|
|
| Bit3= | Auto Jog (0, disable jog detection. If enabled a stop request within | |
|
|
|
| 0.5 second of a start request is forced to 0 stop time). | |
|
|
| Bit4= | Auto Endstop (0, disabled. If enabled detect a stalled motor during | |
|
|
|
| softstop and turn off thyristors). | |
|
|
| Bit5= | Auto Stop (0, do not detect variations in pf during stop smooth stall). | |
|
|
| Bit6= | Auto Endstart (0, disable detection of full speed during start and | |
|
|
|
| end of start ramp) | |
|
|
| Bit7= | Auto Pedestal (0, disable detection of motor rotation at start with | |
|
|
|
| pedestal adjustment). | |
|
|
|
| ||
Parameters | P87 | Under Current 2 (for 2nd param set) | Sets the under current trip level. | ||
Continued |
|
|
|
| |
P88 | Under Current Time 2 (for 2nd param set) | The time allowed for a low current level condition (P87) to exist | |||
| |||||
|
|
| before tripping. For 60 Hz, 40 cycles = 667ms. | ||
|
|
| For 50 Hz, 40 cycles = 800ms. | ||
|
|
|
| ||
| P89 | Current Limit 2 (for 2nd param set) | Sets the motor starting current. | ||
|
|
|
| ||
| 90 | (for 2nd param set) | The time allowed for start current to equal P89 value before tripping. | ||
|
|
| Note that for 60 Hz, 40 cycles = 667ms. | ||
|
|
| For 50 Hz, 40 cycles = 800ms. | ||
|
|
|
| ||
| 91 | Shearpin 2 (for 2nd param set) | Sets the over current trip level. Shearpin operation begins after | ||
|
|
| |||
|
|
|
| ||
| 92 | (for 2nd param set) | The number of cycles allowed for an overcurrent condition before | ||
|
|
| tripping (only when shearpin flag P95, Bit3=1). For 60 Hz, 60 cycles | ||
|
|
| = 1second. For 50 Hz, 50 cycles = 1second. | ||
|
|
|
| ||
| 93 | (for 2nd param set) | Sets the overload current level as a portion of FLA. (P93 is always | ||
|
|
| active but P89 is only active during motor starting.) | ||
|
|
|
| ||
| 94 | (for 2nd param set) | The time allowed for an overload condition before tripping. For 60 | ||
|
|
| Hz, 60 cycles = 1second. For 50 Hz, 50 cycles = 1second. | ||
|
|
|
| ||
| 95 | User Flags 1 (for 2nd param set) | Note that these bits operate with P96 bit 6 (param group selector). | ||
|
|
| This lets you set a primary and secondary group value. | ||
|
|
|
| Definition (Preset Value) | |
|
|
| Bit0= | Kickstart 2 (0, Off) | |
|
|
| Bit1= | Current limit selector 2 (1, On) | |
|
|
| Bit2= | Overload selector 2 (1, On) | |
|
|
| Bit3= | Shearpin selector 2 (0, Off) | |
|
|
| Bit4= | Low current selector 2 (0, Off) | |
|
|
| Bit5= | Thermistor selector 2 (0, Off) | |
|
|
| Bit6= | Unused | |
|
|
| Bit7= | Remote starting 2 (1=P96 Bit4) (If 0, 0=P96 Bit 3) | |
|
|
|
|
| |
| 96 | User Flags 2 (for 2nd param set) |
| Definition (Preset Value) | |
|
|
| Bit0= | Low voltage Softstop (0, Off) | |
|
|
| Bit1= | Not global enable 1(2) (0, Off) | |
|
|
| Bit2= | Not global enable 2(2) (0, Off) | |
|
|
| Bit3= | Keypad Start/Stop 2 (0, Off)- (Available when P95 Bit7=1) | |
|
|
| Bit4= | Remote Start/Stop (0, Off)- (Available when P95 Bit7=0) | |
|
|
| Bit5= | Main contactor 2 (0, Off)- (use with a relay) | |
|
|
| Bit6= | Second Parameter Set 2 (1, On= Group 2) | |
|
|
| Bit7= | Zero Start time 2 (0, Off) | |
|
|
|
| ||
| 97 | Flag1 I/P Source Address | Address of source flag parameter. | ||
|
|
| (Parameter 98 is the mask for P97.) | ||
|
|
|
| ||
| 98 | Flag1 I/P Source Mask | The bit mask for source flag parameter. | ||
|
|
|
| ||
| 99 | Flag1 O/P Destination Address | Address of destination flag parameter. | ||
|
|
| (Parameter 100 is the mask for P99.) | ||
|
|
|
|
| |
MN850 | Parameter Index |