Sharp UX-600M operation manual Timer list, Reception errors

Page 92

Chapter 10 Printing Reports and Lists

Reception errors

	E-0	Able to recognize handshake signal, but it has errors.

	E-1	Line disconnected during reception.

	E-2	Cannot recognize the handshake signal from the transmitter side.

	E-3	Cannot recognize the last handshake signal from the transmitter side.

	E-4	Cannot recognize the handshake signal for next page from the transmitter side in
	E-4	the case of mode change.
		the case of mode change.

	E-5	Cannot recognize the handshake signal for next page from transmitter side.

	E-7	No response from transmitter or "disconnect signal" is received at receiver side.

	E-8	Error occurred upon completion of reception of all pages.

	E-9	Error occurred when mode was changed or transmission/reception switching was
	E-9	performed.
		performed.

	E-10	Error occurred during partial page or physical page reception.

	E-11	Error occurred after or during inquiry from the remote (transmitting) machine as to
	E-11	whether reception was possible or not.
		whether reception was possible or not.

	E-12	Error occurred during or just after fallback.

	E-13	Error occurred after retransmission end command was received.

	E-14	Error occurred after voice communication command was received.

Timer list

This list shows the timer operations which are currently set.

80

Image 92

Contents UX-600M For Your Records Entering your name and number InstallationQuick Reference Guide Sending documents Setting the date and timeStoring and clearing numbers for automatic dialing Receiving Documents Loading paperEntry Mode Function key menuPrint Set-up Introduction Important safety information Trademark acknowledgementsTable of Contents Using the Hookup Optional Hookup Settings Special FunctionsPage Points to keep in mind when setting up InstallationUnpacking Checklist Loading the Imaging Film Do not Discard the Green Gears and the Green FlangeTabs Installation When to replace the imaging film UX-15CR Imaging FilmConnections AC outletTEL Connecting the fax to your computer Windows ’95 users Installing the Multifunction Interface SoftwareWindows 3.1 or higher users Installation Multifunction Interface software manual Attachments Loading Printing Paper Your fax has been set at the factory to Initial Settings Setup GuideRequired settings Settings which may be necessaryLook at the Operation Panel Number keysDisplay Entering Your Name and Fax Number Entering Letters for Names CommentsSymbol list ExampleSetting the Date and Time Daylight Saving Time Stop keySelecting the Reception Mode Setting the reception modeSelecting the receiving unit OFF Setting Distinctive RingList on the previous Storing Numbers for Automatic Dialing Storing numbersReturn to to store another num Making changes Lithium battery keeps automatic dialing numbers in memoryClearing numbers Storing numbers in Group Keys Enter the Speed Dial numbers of the reVolume Adjustment SpeakerHandset RingerSize and weight Sending DocumentsTransmittable Documents Other restrictionsLoading the Document Optional Transmission Settings ResolutionSetting the resolution and contrast ContrastCover Sheet ExampleBatch Page Numbering Dialing and Transmission Normal DialingDirect Keypad Dialing Rapid Key Dialing Speed DialingUsing the HOLD/SEARCH key Press the HOLD/SEARCH keyUsing the Redial key Automatic redialingReceiving Documents Using Auto ModeUsing Manual Mode Receiving documents on an extension phone 1 Print Reception RatioMaking Copies Making Copies Copy Cut-off Making Telephone Calls Rapid Key Dialing Press the approRedial HoldChanging the outgoing message Using the HookupAnswering Machine Hookup Mode key Activating the hookupTesting for proper operation How the hookup operatesIf you have problems If it still doesn’t work How fax transmissions are detected Optional Hookup Settings Quiet Detect TimeFax reception when the answering machine fails Special Functions Blocking Reception of Unwanted FaxesSpecial Functions Memory Sending documents from memorySubstitute reception If the memory becomes fullBroadcasting MemoryBroadcasting using a Group Key Polling Requesting a Fax Transmission Requesting transmissionBeing polled polling standby Polling securityStoring and clearing fax numbers for polling permission Timer Operations Setting a timer operationTo cancel an operation Entering and Using Programs Initial procedureTransmission Polling Broadcasting Clearing a Program keyPress the Program Key Using a Program keyTo cancel a programmed timer operation Settings Optional SettingsAccessing the Settings Optional Settings Setting 8 Dial ModeOptional Settings Setting 15 Polling Activity Report Printing Reports and ListsPrinting a list Transmission errors Explanation of headingsTimer list Reception errorsTelephone Number List Passcode ListOption Setting List Anti Junk Number List Program and Group ListPrint Setup List Transaction ReportMaintenance Fax print headHousing Scanning glass and rollersTroubleshooting Problems and SolutionsTroubleshooting Troubleshooting Messages and Signals Display messagesAudible signals Clearing jammed fax paper Clearing Paper JamsClearing a jammed document Troubleshooting Specifications ResolutionSpecifications Sharp Physical Chemical Characteristics FCC Regulatory Information Introducción de su Nombre y Número Guia de Consulta RapidaInstalación Envio de Documentos Insercion de Fecha y HoraMemorización y Borrado de Numeros de las Marcas Automaticas Recepción de documentos Cargar el papelIndex 101102 103 Page Limited Warranty Sharp Electronics Corporation