Muratec F-98 Programming regular polling, Relay Tx Group No ,24, P2Fax Number 5557312

Press ENTER, ENTER.

Press ENTER. The LCD now shows either

7 Use the numeric keypad to enter the two-digit identifier (01–32) for the first call group. You can specify up to 10 separate groups for each relay broadcast initiation. Between the entry of each new group, press COM-OPTIONSto insert a comma but do not insert a comma after the last group number.

For example, here, we’ve entered 0, 4, COM-OPTIONS, 1, 1, GROUP DIAL, 2, 4:

Relay Tx

Group No. 1,24_

Note: The LCD shows only four characters of the group numbers.

Important: Again, do not insert a comma after the last group number.

When finished, press ENTER.

8 If you want the transmission to begin immediately every time you press the key, press ENTER and skip to step 11.

If you want to delay the transmission (perhaps to take advantage of lower phone rates), press COM-OPTIONS,ENTER.

9 There’s a choice to make. Instruct your fax to carry out this delayed command in one of the following ways:

Option 1: Perform the command once at a certain time on a certain day of the month. (For example, “Do this at 5:05 PM on the 30th.”)

To select this option, use the numeric keypad to enter the date and time when the fax should perform the command:

Delayed

Enter Time: 30/17:05

Option 2: Perform the command at a certain time each day you press the key. (For example, “Do this at 5:05 PM today.”)

To select this option, use the numeric keypad to enter 0, 0 (i. e., 00), and then the time when the fax could perform the command:

Delayed

Enter Time: 00/17:05

10

11 The LCD now displays the next programmable one-touch key.

If you do not want to enter or change any other key’s programming, press STOP to return your machine to its usual standby mode.

If you do want to enter or change this key’s programming, go back to step 3. If you wish to enter or change another key’s programming, go back to step 2.

Beyond the basics

Programming regular polling

Note: To erase a programmable one-touch key, refer to page 2.41.

To program a regular polling operation into a programmable one-touch key:

1 Press PROGRAM, C, 1, ENTER. The LCD either shows:

Select Program No.

P1:No Number Stored

… or indicates a command is already programmed into this key.

If P1 is the key you want to program, skip to step 3. (However, our examples from here will say “P2” rather than “P1.”)

2 Select the key in which you want to program a command or change a previ- ously stored command and then press it. Here, we’ve selected P2.

Select Program No.

P2:No Number Stored

3 If you change your mind and wish to select a different programmable one- touch key, go back to step 2 before going on to step 4.

4

P2:Fax Number	or	P2:Fax Number
_		9-5557312_

5 Use the numeric keypad to enter the number exactly as your machine should dial it, including whatever codes your phone system may require. The num- ber can be up to 40 characters in length:

P2:Fax Number 9-5550696

Your display can show only 20 characters at a time. To view characters beyond those 20 (such as with an international long-distance number), press to scroll leftward or to scroll rightward.

Important: Do not press ENTER.

Note: If you make a mistake or want to erase characters entered in a previ- ous setting, press CANCEL to erase leftward. Or, if you want to change just one character in the number, press to move the cursor leftward, or to move it rightward, to that character and press CANCEL to erase it. Then re-enter until the number is just as you want it.

2.37