Panasonic CY-TUN153U warranty Channel Preset, Preset Channel Calling

Page 10

English

Basic TV Operation

 

Channel Preset

English

Refer to the CQ-VD7003U and CQ-VD6503U

17instruction manuals for information on TV operation on the CQ-VD7003U and CQ-VD6503U touch panel and remote control.

[PWR] (Power)

[ENT] (ENTER)

[BAND] [MENU]

[] (CH DOWN) [] (CH UP)

[] [] (PRESET)

Power

Turn your car’s ignition key to the ACC or ON position. ON: Press [PWR] (Power).

OFF: Press [PWR] (Power) again.

Note:

When changing the source to TV tuner on Head Unit (CQ-VD7003U, CQ-VD6503U, option), the power is turned on automatically.

Band Selection

Press [BAND].

TV1 TV2

Note:

TV2 is provided to allow more preset channels in memory.

Warning

To ensure safety, never attempt to preset channels while you are driving.

Up to 12 channels can be stored in each of the TV1 and TV2 band selections.

TV2 is provided to allow more preset channels in memory. Channels that could not be placed in memory on the Band TV1 can be placed on the Band TV2.

If Band TV1 is sufficient to hold all desired channels, they should usually be preset to that band.

Note:

New channels overwrite existing saved stations after these procedures.

Auto Preset Channel Memory

Writing Preset Channel (PRESET

WRITE)

Favorite channels can be written after you have set the preset channel once.

Example:

The 25 channel is written in the TV1 preset channel list.

Press and hold [] (PRESET) for more than 2 seconds.

Preset channel writing mode display appears.

Press [] (CH DOWN) or [] (CH UP) to select channel you want to write.

18

Channel Selection

Press [] (CH DOWN) or [] (CH UP).

[] (CH UP): Higher channel number

[] (CH DOWN): Lower channel number

Press and hold [] (CH DOWN) or [] (CH UP) for more than 0.5 seconds, then release it. Seeking will start.

TV Channel Display

Press [ENT] (ENTER).

Press [ENT] (ENTER) again to display off.

Example: When preset channel is not set.

TV band

Selected TV channel number

With this operation, channels with good receiving conditions can be automatically stored in the preset memory.

Press [BAND] to select the TV band.

Press and hold [BAND] for more than 2 seconds.

12 channels with first to 12th highest in signal strength will be preset to each band. (They are listed in order, from the earliest channel number.)

Preset Channel Calling

Press [BAND] to select the TV band.

Press [] or [] (PRESET).

TV channel you want to write

Press [ENT] (ENTER) or [BAND] to set.

Press [MENU] to exit the preset channel writing mode.

Deleting Preset Channel (PRESET

DELETE)

Channels can also be deleted from the presets when no longer required.

Example:

The 30 channel is deleted in the TV1 preset channel list.

Press and hold [] (PRESET) for more than 2 seconds.

Preset channel deleting mode display appears and preset 1 channel is received.

Press [] or [] (PRESET) to select preset channel you want to delete.

Note:

Only English is displayed on the OSD screen.

Background of the display becomes blue when the unit cannot get a good reception on the TV.

Selected preset channel number

Preset channel you want to delete

Press [ENT] (ENTER) or [BAND] to set.

Press [MENU] to exit the preset channel deleting mode.

18

 

CY-TUN153U

CY-TUN153U

 

19

 

 

 

 

 

 

Image 10
Contents CY-TUN153U Safety Information Case of battery leakage  Take care not to damage the leadsFeatures Contents Toronto Customer Services Directory Limited WarrantyVancouver Remote Control Unit SettingsPreparation Components Diver Diversity Antenna Setting To use the two TV antennae ProvidedSystem Connection Example TunerRemote Control Unit Names of Controls and Terminals Diver SettingTV Tuner Unit Channel Preset Preset Channel CallingInstallation Hardware For Installation InstallationInstallation Precautions Installation Hardware For WiringMount the unit on the car carpet By using Velcro tape  Mounting the Tuner UnitMounting the TV Antenna Electrical Connections Module CY-EM100UConnecting with Head Unit CQ-VD6503U Yellow Not used Video YellowConnecting with Rear Monitor CY-VHD9401U When Connecting the Rear Monitor CY-V7001U, option Check the wiring TroubleshootingProblem Possible cause  Possible solution CommonSpecifications Tuner for Analog TV onlyInformations concernant la sécurité Mise en gardeInformations concernant la sécurité suite Caractéristiques Raccordement du fil de Connexion du frein à mainRéparation Sous Garantie Répertoire des services à la clientèle Garantie limitéeLimitations ET Exclusions Préparatifs Pièces TélécommandeRemplacement de la pile RéglagesPour utiliser les deux antennes Fournies Antenne de télévision diversitéRéglage d’antenne Diver Diversité VD6503U, module d’extension CY-EM100U et syntonisateur téléCet appareil ne peut pas fonctionner de manière autonome Exemple de raccordement à la chaîneVD6503U et syntonisateur télé Syntoniseur télé CY-TUN153URéglages de Diver TélécommandeSyntoniseur télé Commandes de base du téléviseur Présyntonisation de canal Rappel de canal PrésyntoniséInstallation PréparatifsMontage du syntonisateur Installation suiteRecommandé La vis autotaraudeuseMontage de l’antenne de télévision Module d’extension CY-EM100U Raccordements électriquesSyntoniseur télé CQ-VD7003U Raccordements électriques suiteUnité d’opération UnitéTV OUT Raccordement à l’unité d’opération CQ-VD7001UCQ-VD7001U TV-CONTSi vous soupçonnez une anomalie DépannageProblèmes communs suite Dépannage suite Fiche techniqueRespete las siguientes advertencias durante la instalación Información de seguridadAdvertencia Incluso LA MuertePrecaución Información de seguridad continuaciónRespete las siguientes precauciones durante la instalación Contenido CaracterísticasAjustes Preparativos ComponentesUnidad de mando a distancia Para utilizar las dos antenas de Televisión suministradas Antena de televisión de diversidadAjuste de antena Diver Diversidad Para usar las dos antenas OpcionalesEsta unidad no funciona por sí sola Ejemplo de conexión del sistemaExpansión CY-EM100U y sintonizador de televisión Dispositivos conectadosUnidad de mando a distancia Power SupplyNombre de controles y terminales Ajustes Diver BandSelección de los canales Presintonizados Precauciones sobre la instalación InstalaciónPreparativos Hardware para la instalación Para la instalaciónEstacionamiento freno de mano Montaje de la unidad del sintonizadorConexión del cable de conexión del freno de Freno de manoPara mejorar la fijación, tenga en cuenta lo siguiente Inserte la placa de conexión a tierraPreparativos Del cuerpo de la antena y péguelo. aMódulo de expansión CY-EM100U Conexiones eléctricasConexión de la unidad principal CQ-VD7003U y el Sintonizador de TVUnidad principal CQ-VD6503U Conexiones eléctricas continuaciónUnidad principal AV2-IN To Head Unit Video RemoteAl conectar el monitor trasero CY-V7001U, opción Conexión a la unidad principal CQ-VD7001UConexión al monitor posterior CY-VHD9401U Monitor traseroSi sospecha que algo no funciona Solución de problemasComún Solución de problemas continuación Especificaciones Panasonic Canada Inc