Rotel owner manual Operating the RR-1050

96RR-1050

Att programmera en Enhets/IngŒngs-knapp eller EXT-knappen som skall vŠlja en ingŒngskŠlla fšr den enhet som skall styras:

1.Tryck pΠLEARN-knappen pΠRR-1050. LEARN- indikatorn blinkar nu i displayen.

2.Tryck och hŒll ned den Enhets/IngŒngs-knapp pŒ RR-1050 vars kommando-koder skall programmeras tills LEARN-indikatorn slutar blinka. BenŠmningen pŒ den valda knappen visas i displayen.

3.Tryck och hŒll ned motsvarande knapp pŒ den sŠndande fjŠrrkontrollen (original fjŠrrkontrollen) tills texten ÓOK!Ó visas i displayen som bekrŠftar att kommandot har lŠrts upp.

Upprepa Steg 2 och 3 fšr varje Enhets/IngŒngs-knapp som du vill programmera.

OBS! AUD-knappen kan inte programmeras fšr val av ingŒngskŠlla.

Meddelanden dΠman programmerar RR-1050:

Om displayen visar ÓERRORÓ, lyckades inte programmeringen. Fšrsšk igen.

Om displayen visar ÓNO DATAÓ, togs det inte emot nŒgon IR-signal frŒn den sŠndande fjŠrrkontrollen. Justera placeringen av de bŒda fjŠrrkontrollerna och fšrsšk igen.

RR-1050 lŠmnar programmeringslŠget nŠr en knapp inte tryckts pŒ 15 sekunder.

UpplŠrning av knapp fšr multi-funktion

De fem knapparna SCAN, PTY, P-TUN, TP och TA har en speciell egenskap. De lŠras upp till att innehŒlla upp till tre olika kommandon pŒ enda knapp. Vid fšrsta tryckningen pŒ knappen skickas det fšrsta kommandot, det andra kommandot skickas vid andra tryckningen och det tredje kommandot skickas vid tredje tryckningen.

Fšr att programmera en multifunktions-knapp t.ex. SCAN- knappen :

1.Fšlj de fyra stegen i avsnittet ÓAtt programmera en Kommando-knappÓ som beskrivits tidigare fšr att programmera det fšrsta kommandot fšr SCAN- knappen.

2.Tryck pŒ SCAN-knappen en andra gŒng. ÓS1-2Ó visas nu i displayen. Tryck och hŒll ned nŠsta knapp pŒ originalfjŠrrkontrollen tills ÓOK!Ó visas i displayen.

English 9

Secondary Command Buttons

Under the sliding cover is a group of oval buttons which provide secondary command functions. The function of these buttons varies depending on the device selected with the DEVICE/INPUT buttons. See the ÒLabel SetsÓ illustra- tion.

Multi-Step Buttons

In addition to normal functions, the five buttons labeled SCAN, PTY, P-TUN, TP and TA provide a special option Ð learning up to three commands on a single button. The first command is sent when the button is pressed once, the second command is sent the next time the button is pressed, and the third command is sent the third time the button is pressed.

Special Buttons

Three rectangular buttons behind the sliding cover are used for programming the RR-1050 and for other special features such as the KEY TONE feature.

Configuration Buttons

Four recessed buttons behind the sliding cover are used in configuring the unit. These buttons are recessed to pre- vent pressing them accidentally. Use the tip of a ballpoint pen to press them.

Operating the RR-1050

This section of the manual explains the basic operation of the RR-1050 and most of its standard features.

NOTE: The AUD DEVICE/INPUT button of the RR-1050 is pre-programmed with control codes for Rotel audio/video receivers or surround sound processors. The V1 button is pre-programmed to operate Rotel DVD play- ers. The other DEVICE/INPUT buttons (CD, TUN, TAPE and V2 - V5) are unprogrammed. You must use the LEARNING function to program control codes for these DEVICE/INPUT buttons.

Sending IR Commands

Instead of putting down one remote and picking up an- other, you simply press a button on the RR-1050 to con- vert it from the remote control for your CD player to the remote control for your TV set. HereÕs how:

1.Press a DEVICE/INPUT button to activate the com- mand set for the desired component. For example, press the AUD button for a Rotel audio/video receiver or surround sound processor. The label for your se- lection appears in the display. The selected command set remains active until you press a different DEVICE button.