SMSC COM20020 manual NON-MULTIPLEXED BUS, 80XX-LIKE Control Signals Read Cycle

Page 50

A0-A2

VALID

t1

nCS

t3

t5

nRD

t2

t4

t6

t7

D0-D7	VALID DATA
Parameter	min	max	units

t1	Address Setup to nRD Active
t2	Address Hold from nRD Inactive
t3	nCS Setup to nRD Active
t4	nCS Hold from nRD Inactive
t5	Cycle Time (nRD Low to Next Time Low)
t6	nRD Low to Valid Data
t7	nRD High to Data High Impedance

15nS

10nS

5**nS

0nS

4T*		nS
	40	nS
0	20	nS

*T is the Arbitration Clock Period.

T is identical to XTAL1 if SLOW ARB = 0, T is twice XTAL1 period if SLOW ARB = 1

**nCS may become active after control becomes active, but the access time will now be 45nS measured from the leading edge of nCS.

Note 1: The Microcontroller typically accesses the COM20020 on every other cycle. Therefore, the cycle time specified in the microcontroller's datasheet should be doubled when considering back-to-back COM20020 cycles.

FIGURE 12 - NON-MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; READ CYCLE

50

Image 50

Contents Features General DescriptionTable of Contents PIN Configuration Description of PIN Functions A1,A2/ALEMiscellaneous DIP PIN Plcc PIN Name Symbol DescriptionTransmission Media Interface Instead, it must be connected to XTAL1 with COM20020 Operation Network Protocol Network ReconfigurationProtocol Description Data RatesResponse Time Extended Timeout FunctionBroadcast Messages Line Protocol Reconfiguration TimeIdle Time Invitations To TransmitNegative Acknowledgements Data PacketsAcknowledgements System Description MULTIPLEXED, 8051-LIKE BUS Interface with RS-485 Interface Figure C Backplane Configuration Traditional Hybrid InterfaceCOM20020 Network Using RS-485 Differential Transceivers Differential Driver Configuration Programmable Txen PolarityInternal Block Diagram Nominal Functional DescriptionAttenuation Cable Type Impedance AT 5MHZRead Register Summary Write Data Register Internal RegistersInterrupt Mask Register IMR Tentative ID RegisterNext ID Register Diagnostic Status RegisterCommand Register Status RegisterConfiguration Register Setup Register BIT BIT Name Symbol Description BIT BIT Name Symbol Description DupidData Command Description Address Pointer High Register Address Pointer Low RegisterConfiguration Register ResetCKP3 CKP2 CKP1 Sequential Access Operation Internal RAM Sequential Access MemoryAccess Speed Software InterfaceSelecting RAM Page Size Transmit SequenceRAM Buffer Packet Configuration Page Receive Sequence Command Chaining Transmit Command ChainingReceive Command Chaining Reset Details Internal Reset LogicImproved Diagnostics Initialization SequenceNormal Results Abnormal ResultsOscillator Parameter Symbol MIN TYP MAX Unit Comment Maximum Guaranteed RatingsDC Electrical Characteristics Operational DescriptionXTAL1, XTAL2 Input Capacitance Timing Diagrams Multiplexed BUS, 68XX-LIKE Control Signals Read CycleMultiplexed BUS, 80XX-LIKE Control Signals Read Cycle Multiplexed BUS, 68XX-LIKE Control Signals Write Cycle Multiplexed BUS, 80XX-LIKE Control Signals Write Cycle NON-MULTIPLEXED BUS, 80XX-LIKE Control Signals Read Cycle NON-MULTIPLEXED BUS, 68XX-LIKE Control Signals Read Cycle NON-MULTIPLEXED BUS, 80XX-LIKE Control Signals Write Cycle NON-MULTIPLEXED BUS, 68XX-LIKE Control Signals Write Cycle Normal Mode Transmit or Receive Timing These signals are to and from the hybridNTXEN NPULSE1 TTL Input Timing on XTAL1 PIN 28-PIN Plcc Package Dimensions 24-PIN DIP Package Dimensions Date SECTION/FIGURE/ENTRY Correction RevisedStandard Microsystems Corp