Britax Child Seat This child seat must not be used forward, Who weigh less than 9.1 kg 20 lbs

Page 11

Installation : Forward-Facing

Lower Universal Anchorage System (LUAS) Installation

Figure A illustrates a typical forward-facing LUAS

 

 

 

installation.

 

 

Verify that your vehicle is equipped with LUAS

 

 

 

anchors. If LUAS anchors are not available, you must

 

 

 

use vehicle belt installation methods.

 

 

 

WARNING!

A Forward-facing

 

• This child seat must NOT be used forward-

Release

 

 

facing for children less than one year of age OR

Top

 

who weigh less than 9.1 kg (20 lbs).

Button

 

 

• This child seat must be in full upright position

 

 

 

when installed forward-facing.

 

 

 

• Always use the Versa-Tether when the child seat

 

 

 

is installed forward-facing. Check your vehicle

B

 

 

owner’s manual for approved tether anchor

 

 

locations.

 

 

IMPORTANT: Check that the LCS connector strap is

 

 

tight and not twisted, and that the LCS connectors

 

 

are in an upright position (Fig. B) to ensure proper

 

 

installation.

 

 

1

Remove the LCS connectors from storage slots

C

 

 

under the cover. See page 28. Pull both LCS

 

 

connectors completely through the child seat’s

 

 

 

right-side, rear-facing belt slot (Fig. C) so they

 

 

 

are on the outside of the shell.

 

 

NOTE : Child seat is assembled in rear-facing

 

 

mode.

 

 

2

Press and hold one LCS adjuster release button,

 

 

 

then pull to extend the LCS strap to full length.

D

 

 

Repeat on the other end of the strap.

 

3

Thread the appropriate LCS connector through

 

the forward-facing belt path (Fig. D) at the back of the child seat.

Installation : Forward-Facing

4Place the child seat sideways in the upright position on the vehicle seat with the back of the child seat facing you.

5Remove the Versa-Tether from the pouch and place up and over the child seat back.

6Verify that the LCS strap is not twisted and attach

the closest LCS connector to the vehicle seat back

e

to the farthest LUAS anchor (Fig. B).

 

 

A positive click confirms attachment.

NOTE : It may be necessary to switch LCS connectors as shown on page 28 if ANY of the following

conditions exist :

 

• LCS connector is not in an upright position (Fig. D).

 

• LCS strap is twisted.

 

• A positive click is NOT heard when the LCS connector

F

connects to the LUAS anchor.

NOTE : If a positive click is not heard, but the LCS

connector is in an upright position, you should not switch the LCS connector. The strap may be too tight or twisted, or there may be debris in the LCS connector.

7Rotate the child seat into the forward-facing position.

8Verify that the LCS strap is not twisted and attach the remaining LCS connector to the adjacent LUAS anchor (Fig. D).

A positive click confirms attachment.

9Push the child seat into the vehicle seat while pulling the LCS adjuster strap tight (Fig. F). Ensure the bottom of the child seat base is in full contact with the vehicle seat.

10Attach the Versa-Tether®hook to the designated tether anchor for the chosen seating position. Remove all slack from the tether to secure. Store any excess webbing in the tether pouch. See pages 25 – 27.

11Verify all connections are secure and that the child seat is stable.

The child seat is secure when it cannot be moved front-to-back or side-to-side more than 2.5 cm (1 inch) at the belt path. If the child seat is not secure, repeat the procedure or use an alternate seating location.

18

19

Image 11
Contents Roundabout Table of Contents Secure the top tether strap provided with this child seat Registration Important NotesCertification Rear-Facing Important Harness AdjustmentsInches When the top of the child’s ears are below the top Forward-FacingChild Seat Features Vehicle Seating Positions Vehicle Safety BeltsSee diagram below Vehicle Buckle PositionsIntended Lower Universal Anchorage System Luas InstallationIf stored, remove the LCS strap and connectors Vehicle belt can be routed over or under the cover Lap-Shoulder Belt InstallationPosition the lap belt portion through the open Car is parked on a level surface Fig. F Lap-Belt InstallationHas and how to lock the retractor Lock-off is properly closed when a positive click is heardUnder the cover. See page 28. Pull both LCS This child seat must not be used forwardWho weigh less than 9.1 kg 20 lbs LocationsAForward-facing Lap-Belt Installation Forward-Facing Installation Safety InformationRear-Facing Installation Tether Connector Strap Using the Versa-TetherChest Clip Switching the Lower Connector System LCSRecline Adjustment Storing the LCS ConnectorsReleasing the Harness Buckle How to Adjust Harness Slot HeightHarness Buckle Fastening the Harness BuckleChild Seat Cover Removal Child Seat Functions Care and MaintenanceRe-threading the Harness Buckle Harness Buckle RemovalWarranty Cleaning the Harness BuckleInstallation sangle Versa-Tether Mise EN GARDE  Enregistrement Remarques importantesHomologation Qui sont âgés dau moins un an et Important réglage du harnaisSiège orienté face à larrière Face à lavantSous la housse Positions assises du véhicule Voir le diagramme ci-dessousCeintures de sécurité du véhicule Positions de la boucle de ceinture du VéhiculeInstallation avec système dancrage universel au bas Luas Lorsque les connecteurs Luas ne sont pas utilisés, toujours Installation avec ceinture à trois points dappuiDauto.sur une surface horizontale figure F.90º Installation avec ceinture sous-abdominaleSi nécessaire, on peut obtenir le bon angle dinclinaison f Larrière Remarque Si lon nentend pas un déclic positif mais que leEst faite correctement CoquilleJeu de la sangle dattache pour obtenir une fixation Face à lavant avec ceinture à trois points dappuiVerrouiller le rétracteur Mise EN Garde Consignes de sécurité Installation dans un avionInstallation du siège orienté face à lavant Sur la sangle dattache Sangle de connexion dattacheUtilisation de la sangle Versa-Tether Repérez un point d’ancrage fixe qui soitRemarque Les sièges dauto sont livrés par Britax avec Interversion du système à connecteur bas LCSRangement des connecteurs LCS Boucle pour les retirer de la boucle figure B Boucle du harnaisTenir la boucle du harnais avec une main De poitrine par les fentes inférieures dans la housse Retrait de la housse du siège dautoRetirerdoucementlapartiesupérieuredelahousse. f DautoNettoyer À Léponge avec de leau tiède et un savon doux Retrait de la boucle du harnaisPassage de la boucle du harnais Garantie Nettoyage de la boucle du harnaisIMPORTANT