Britax manual Child Seat Cover Removal, Child Seat Functions Care and Maintenance

Page 18

Child Seat Functions

Care and Maintenance

6Position harness straps around the child and fasten the harness buckle (Fig. A) and chest clip (Fig. B).

•Proper connection of the harness buckle is confirmed with a positive click after inserting each buckle tongue.

•If the buckle will not fasten with a positive click after inserting each buckle tongue, the harness buckle or adjuster area may be clogged with food, drink or other debris that needs to be removed. See page 36 for cleaning instructions.

IMPORTANT: Gently pull up on the harness straps to tighten lap section of the harness which should fit across the child’s upper thighs.

7Slowly pull the adjuster strap to tighten the harness around the child (Fig. C).

8Position the chest clip at the middle of the child’s chest, level with the armpits (Fig. D).

9Verify that harness is not twisted and child is properly secured.

IMPORTANT:

•Always pull on the harness after securing the child to ensure the buckle tongues are secure in the harness buckle.

•Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. The harness should have a comfortable but snug fit around the child. You should not be able to pinch excess webbing at the shoulder once the harness is properly secured.

a

b

c

d

Child Seat Cover Removal

WARNING! Do not take apart the harness. Never remove the buckle tongues from the harness. They cannot be reattached after removal. If reassembled incorrectly, the child seat may not perform as intended.

1Loosen the harness by pressing the harness adjuster release button while pulling the harness straps forward as far as possible.

2Unhook the harness straps from the harness yoke on rear of child seat (Fig. E).

3Pull the upper harness straps through the e shell and cover to the front of child seat.

4Remove the harness buckle and belly pad by turning the metal buckle strap retainer of the

harness buckle on the underside of the child

seat so the short side will slide through the child seat shell (Fig. F).

5Gently remove the upper portion of the cover. Be careful not to damage the energy- f absorbing foam.

6Push the metal buckle strap retainer through the slots in the shell and cover to the top of the child seat.

7Pull the lower harness straps, buckle tongues, and chest clip through lower slots in cover.

8Remove the entire cover from child seat.

32

33

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Roundabout Table of Contents Secure the top tether strap provided with this child seat Important Notes CertificationRegistration Forward-Facing Important Harness AdjustmentsInches When the top of the child’s ears are below the top Rear-FacingChild Seat Features Vehicle Buckle Positions Vehicle Safety BeltsSee diagram below Vehicle Seating PositionsLower Universal Anchorage System Luas Installation If stored, remove the LCS strap and connectorsIntended Lap-Shoulder Belt Installation Position the lap belt portion through the openVehicle belt can be routed over or under the cover Lock-off is properly closed when a positive click is heard Lap-Belt InstallationHas and how to lock the retractor Car is parked on a level surface Fig. FLocations This child seat must not be used forwardWho weigh less than 9.1 kg 20 lbs Under the cover. See page 28. Pull both LCSAForward-facing Lap-Belt Installation Safety Information Rear-Facing InstallationForward-Facing Installation Using the Versa-Tether Tether Connector StrapStoring the LCS Connectors Switching the Lower Connector System LCSRecline Adjustment Chest ClipFastening the Harness Buckle How to Adjust Harness Slot HeightHarness Buckle Releasing the Harness BuckleChild Seat Functions Care and Maintenance Child Seat Cover RemovalHarness Buckle Removal Re-threading the Harness BuckleCleaning the Harness Buckle WarrantyInstallation sangle Versa-Tether Mise EN GARDE  Remarques importantes HomologationEnregistrement Face à lavant Important réglage du harnaisSiège orienté face à larrière Qui sont âgés dau moins un an etSous la housse Positions de la boucle de ceinture du Véhicule Voir le diagramme ci-dessousCeintures de sécurité du véhicule Positions assises du véhiculeInstallation avec système dancrage universel au bas Luas Installation avec ceinture à trois points dappui Lorsque les connecteurs Luas ne sont pas utilisés, toujoursInstallation avec ceinture sous-abdominale Si nécessaire, on peut obtenir le bon angle dinclinaison fDauto.sur une surface horizontale figure F.90º Coquille Remarque Si lon nentend pas un déclic positif mais que leEst faite correctement LarrièreFace à lavant avec ceinture à trois points dappui Verrouiller le rétracteurJeu de la sangle dattache pour obtenir une fixation Mise EN Garde Installation dans un avion Installation du siège orienté face à lavantConsignes de sécurité Repérez un point d’ancrage fixe qui soit Sangle de connexion dattacheUtilisation de la sangle Versa-Tether Sur la sangle dattacheInterversion du système à connecteur bas LCS Rangement des connecteurs LCSRemarque Les sièges dauto sont livrés par Britax avec Boucle du harnais Tenir la boucle du harnais avec une mainBoucle pour les retirer de la boucle figure B Dauto Retrait de la housse du siège dautoRetirerdoucementlapartiesupérieuredelahousse. f De poitrine par les fentes inférieures dans la housseRetrait de la boucle du harnais Passage de la boucle du harnaisNettoyer À Léponge avec de leau tiède et un savon doux Nettoyage de la boucle du harnais GarantieIMPORTANT 
Top Page Image Contents