Bosch Appliances VG5 600 user manual 2Using a Pelco Controller, New Fast Address Saved Setup Menu

Page 32

32 en Alternative Control Protocols

AutoDome 600 Series Analog PTZ Camera

 

 

6.The on-screen display menu confirms that the VG4 AutoDome stored the FastAddress and then returns to the Main menu with the new Fast Address displayed. Move the joystick to highlight EXIT, and then press FOCUS or IRIS to exit the menus.

New Fast Address Saved

Setup Menu

 

Exit...

 

Command Lock:

OFF

Bosch Menu

 

Camera Setup

 

PTZ Setup

 

Edit Password

 

*FastAddress:

3

Software Version

 

Ack and Reset Alarms

 

Restore All Settings

 

* = Factory Setting

 

Focus / Iris: Select

 

4.1.2Using a Pelco Controller

This section provides instructions to set a FastAddress with a Pelco keyboard or controller.

– An AutoDome with an address set to 0 responds to commands set to any address.

Pelco-Pprotocol must use addresses 1 to 32.

Pelco-Dprotocol must use addresses 1 to 254.

NOTICE!

A previously configured AutoDome with an address above 32 (Pelco-P upper limit) or 254 (Pelco-D upper limit) can be used without readdressing the unit. However, no two (2) addresses can be the same. For example:

Pelco-P addresses above 32 are repeated in multiples of 32 (1, 33, 65, 97 are the same). Pelco-D addresses above 254 are repeated in multiples of 254 (1, 255, 509, 763 are the same).

Setting FastAddress with a Pelco Keyboard

1.Press and hold 95-PRESETfor two seconds to open the Pelco Setup menu.

2.Move the joystick to select the Command Lock menu.

3.Press the FOCUS or the IRIS button to turn Command Lock to OFF.

4.Move to the FastAddress menu and press the FOCUS or the IRIS button to open the menu.

5.Use the joystick to enter the unique identifier for the VG4 AutoDome.

Move the joystick up or down to select the number.

Move the joystick right to move to the next number position.

6.Move the joystick right to select Continue. Then, press the FOCUS or the IRIS button.

7.Use the keyboard to enter the FastAddress number. Then, press the Camera button. Note: You must first clear an assigned FastAddress number to use the number for a different VG4 AutoDome.

F.01U.270.005 2.0 2012.06

User Manual

Bosch Security Systems, Inc.

Image 32
Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Bosch Menu locked PTZ Setup unlocked Other Menus Keyboard Commands by Number Advanced FeaturesTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexPowering On Getting StartedEstablishing AutoDome Control For each of the system componentsLCD Keyboard CommandsBasic Keyboard Operation Setting the Camera Address FastAddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSetting Passwords Special PasswordsPassword Security Level To set or change a password locked commandSetup Menu To open the main Setup Menu locked commandSetup Menu On-Screen Display Menu NavigationCamera Setup Menu ATW AutoInternal OFFLens Setup PALExit Auto Focus Auto IrisPTZ Setup Menu SpotConstant FastNormal Display Setup Menu MomentaryEdit Scene Title to access Sector 1-16 Press Focus/Iris to blank orPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Alarm I/O Setup Inputs SetupInputs NoneOutputs Setup Menu Outputs SetupAlarm Relay OutputsRule Rule Setup MenuRule Setup None Language Menu Advanced Feature Setup MenuAdvanced Feature Setup Diagnostics Menu Bist 11.1 Alarm Status Submenu 2Setting Preset Shots Common AutoDome User Commands unlockedSetting AutoPan Mode 4Configuring Preposition Tours Specifying a Shot or a Sector TitleTo start Preposition Tour To stop a Preposition Tour5Programming the Inactivity Operation 6Recording ToursAlternative Control Protocols Setting FastAddress with Alternative ProtocolsUsing an American Dynamics Controller Exit Command Lock Enter FastAddressFastAddress Setting FastAddress with a Pelco Keyboard 2Using a Pelco ControllerNew Fast Address Saved Setup Menu Pelco Protocol Mode Hardware ConfigurationPelco Keyboard Commands Keyboard Command User Action Description PatternAux On / Aux Off Aux OnSpecial Preset Commands Preset Command DescriptionPreset Initiates Preset TourPelco On-Screen Menus Bosch Menu locked Command Lock lockedPelco menu Bosch menu Setup Menu PTZ Setup unlocked Camera Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Advanced Features Alarm RulesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Example 3 Advanced Alarm Rule using AutoTrack Click the Online Config button and then expand AlarmClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Settings and Recommendations AutoTrack OperationAutoTrack Optimization Mount/Mounting Surface StabilityField of View Unwanted MotionSetting AutoTrack Optimization Parameters Virtual MaskingPrivacy Masking Consistent Light ConditionsPreset positions 90 through Motion Detection with Region of InterestImage Stabilization 7Pre-position TourAzimuth Range Compass Direction Setting the Azimuth Zero Point8Azimuth, Elevation, and Compass Directions AutoHome Recalibration Commands and Settings Function Command Description Key NumberDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayUsing the AutoHome Recalibration Preset or Recorded TourSetting Values AutoHome Recalibration OperationTroubleshooting Guide If O.K., then If using a non-Bosch power supplyIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlIf amber LED does not light when given PTZ commands, then Cannot access userSettings No camera controlSetting FastAddress Does not switch If O.K., then Automatically whenWith an American Dynamics KeyboardOn monitor display Inside of OutdoorLow Voltage flashing 2VG5 Series AutoDome Audio Audio Connections with an VG5 600 Series AutoDomeProblem Solution No Audio Problem Solution If O.K., then Poor AudioUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Group Appendix FastAddress ConversionsBlock Index NumericsCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc