Bosch Appliances VG5 600 user manual Bist

Page 24

24 en On-Screen Display Menu NavigationAutoDome 600 Series Analog PTZ Camera

Menu

Description

Sub-menu / Description

 

 

 

 

Exit

Saves and exits the menu.

 

 

 

 

 

Alarm Status

Enters the Alarm Status menu and displays the

Alarm Inputs 1 to 7, Alarm Outputs 1

 

real time status of alarm inputs and outputs.

to 3 and Alarm Relay

 

 

 

BIST

Enters the Perform Built-in Self Tests menu. If

YES to start test. NO to exit the

 

confirmed, the BIST tests start and the results

menu.

 

 

are displayed.

Typical results displayed as follows:

 

 

BIST

 

 

 

Exit...

 

 

 

Data Flash:

PASS

 

 

Bilinx:

PASS

 

 

FPGA:

PASS

 

 

Digital I/O 1:

PASS

 

 

Digital I/O2:

PASS

 

 

VCA:

PASS

 

 

Homing:

PASS

 

 

 

 

Internal Temp.

Displays the current dome temperature.

 

 

 

 

 

 

High Temp Events

Displays the number of times the high

 

 

 

temperature threshold is exceeded.

 

 

 

 

 

 

Highest Temp

Displays the highest temperature reached.

 

 

 

 

 

 

Low Temp Events

Displays the number of times the low

 

 

 

temperature threshold is exceeded.

 

 

 

 

 

 

Lowest Temp

Displays the lowest temperature reached.

 

 

 

 

 

 

Security Access

Displays the number of times the locked-

 

 

 

command menu is unlocked.

 

 

 

 

 

 

CTFID Access

Displays the number of times the Configuration

 

 

 

Tool is accessed.

 

 

 

 

 

 

Homing Events

Displays the number of times the AutoDome was

 

 

 

rebooted.

 

 

 

 

 

 

Homing Failed

Displays the number of times the AutoDome

 

 

 

failed to home properly.

 

 

 

 

 

 

Loss Home Events:

Displays the number of times the AutoDome lost

 

 

 

the home position.

 

 

 

 

 

 

Home Position Good

Displays if the current AutoDome home position

 

 

 

is good. Displays YES if good.

 

 

 

 

 

 

Restart Events

Displays the number of restart events.

 

 

 

 

 

 

Low Volt Events

Displays the number of times the AutoDome

 

 

 

dropped below the acceptable voltage limit.

 

 

 

 

 

 

Power Up Events

Displays the number of power up events.

 

 

 

 

 

 

Video Loss Events

Displays the number of time that video was lost.

 

 

 

 

 

 

F.01U.270.005 2.0 2012.06

User Manual

Bosch Security Systems, Inc.

Image 24
Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Bosch Menu locked PTZ Setup unlocked Other Menus Keyboard Commands by Number Advanced FeaturesTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexPowering On Getting StartedEstablishing AutoDome Control For each of the system componentsKeyboard Commands Basic Keyboard OperationLCD Setting the Camera Address FastAddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSetting Passwords Special PasswordsPassword Security Level To set or change a password locked commandSetup Menu To open the main Setup Menu locked commandSetup Menu On-Screen Display Menu NavigationCamera Setup Menu ATW AutoInternal OFFLens Setup PALExit Auto Focus Auto IrisPTZ Setup Menu SpotConstant FastNormal Display Setup Menu MomentaryEdit Scene Title to access Sector 1-16 Press Focus/Iris to blank orPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Alarm I/O Setup Inputs SetupInputs NoneOutputs Setup Menu Outputs SetupAlarm Relay OutputsRule Setup Menu Rule SetupRule None Advanced Feature Setup Menu Advanced Feature SetupLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Common AutoDome User Commands unlocked Setting AutoPan Mode2Setting Preset Shots 4Configuring Preposition Tours Specifying a Shot or a Sector TitleTo start Preposition Tour To stop a Preposition Tour5Programming the Inactivity Operation 6Recording ToursSetting FastAddress with Alternative Protocols Using an American Dynamics ControllerAlternative Control Protocols Exit Command Lock Enter FastAddressFastAddress 2Using a Pelco Controller New Fast Address Saved Setup MenuSetting FastAddress with a Pelco Keyboard Pelco Protocol Mode Hardware ConfigurationPelco Keyboard Commands Keyboard Command User Action Description PatternAux On / Aux Off Aux OnSpecial Preset Commands Preset Command DescriptionPreset Initiates Preset TourPelco On-Screen Menus Command Lock locked Pelco menu Bosch menu Setup MenuBosch Menu locked PTZ Setup unlocked Camera Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Advanced Features Alarm RulesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Example 3 Advanced Alarm Rule using AutoTrack Click the Online Config button and then expand AlarmClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Settings and Recommendations AutoTrack OperationAutoTrack Optimization Mount/Mounting Surface StabilityField of View Unwanted MotionSetting AutoTrack Optimization Parameters Virtual MaskingPrivacy Masking Consistent Light ConditionsPreset positions 90 through Motion Detection with Region of InterestImage Stabilization 7Pre-position TourSetting the Azimuth Zero Point 8Azimuth, Elevation, and Compass DirectionsAzimuth Range Compass Direction AutoHome Recalibration Commands and Settings Function Command Description Key NumberDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayUsing the AutoHome Recalibration Preset or Recorded TourSetting Values AutoHome Recalibration OperationTroubleshooting Guide If O.K., then If using a non-Bosch power supplyIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlIf amber LED does not light when given PTZ commands, then Cannot access userSettings No camera controlSetting FastAddress Does not switch If O.K., then Automatically whenWith an American Dynamics KeyboardInside of Outdoor Low Voltage flashingOn monitor display 2VG5 Series AutoDome Audio Audio Connections with an VG5 600 Series AutoDomeProblem Solution No Audio Problem Solution If O.K., then Poor AudioUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Appendix FastAddress Conversions BlockGroup Index NumericsCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc