Bosch Appliances VG5 600 user manual Pelco On-Screen Menus

Page 36

36 en Pelco On-Screen MenusAutoDome 600 Series Analog PTZ Camera

5	Pelco On-Screen Menus
	You can program the AutoDome through the Pelco on-screen display (OSD) menus. To access
	the Pelco menus, you must configure the AutoDome for Pelco Mode and invoke the Pelco
	main Setup Menu.
5.1	Setup Menu
	The Pelco main Setup Menu provides access to the programmable AutoDome settings. Some
	menu items are locked and require a system password to use. Menu items marked with an *
	are the default settings.
	To open the Pelco main Setup Menu (locked commands):
	1. Press 95-PRESET(press the PRESET button for approximately 2 seconds to open).
	2.	Use the joystick to highlight a menu item.
	3.	Press either the Focus or the Iris key to open a menu item.
	4.	Follow the on-screen instructions at the bottom of the screen.

			Setup Menu
			Exit...
			Command Lock:	OFF
			Bosch Menu
			Camera Setup
			PTZ Setup
			Edit Password
			*FastAddress:	Not Set
			Advanced
			Software Version
			Ack and Reset Alarms
			Restore All Settings
			Reset All Memory
			* = Factory Setting
			Focus / Iris: Select

NOTICE!

Use Zoom to select the Exit item from anywhere in a menu.

Menu	Description

Exit	Exits the menu.

Command Lock	Allows or prohibits accessing locked commands. (If password is
(locked)	set, you are prompted to enter the password.

Bosch Menu (locked)	Accesses the full AutoDome configuration menu and all AutoDome
	settings.

Camera Setup	Accesses the White Balance and Night Mode camera settings.

PTZ Setup	Accesses the tours, tour periods, scan speed, edit presets, limit
	stops, recording, and AutoPivot settings.

Edit Password	Changes the password.
(locked)

FastAddress (locked)	Sets or changes a camera address.

F.01U.270.005 2.0 2012.06

User Manual

Bosch Security Systems, Inc.

Image 36

Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Bosch Menu locked PTZ Setup unlocked Other Menus Keyboard Commands by Number Advanced FeaturesTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexPowering On Getting StartedEstablishing AutoDome Control For each of the system componentsKeyboard Commands Basic Keyboard OperationLCD Setting the Camera Address FastAddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSetting Passwords Special PasswordsPassword Security Level To set or change a password locked commandSetup Menu To open the main Setup Menu locked commandSetup Menu On-Screen Display Menu NavigationCamera Setup Menu ATW AutoInternal OFFLens Setup PALExit Auto Focus Auto IrisPTZ Setup Menu SpotConstant FastNormal Display Setup Menu MomentaryEdit Scene Title to access Sector 1-16 Press Focus/Iris to blank orPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Alarm I/O Setup Inputs SetupInputs NoneOutputs Setup Menu Outputs SetupAlarm Relay OutputsRule Setup Menu Rule SetupRule None Advanced Feature Setup Menu Advanced Feature SetupLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Common AutoDome User Commands unlocked Setting AutoPan Mode2Setting Preset Shots 4Configuring Preposition Tours Specifying a Shot or a Sector TitleTo start Preposition Tour To stop a Preposition Tour5Programming the Inactivity Operation 6Recording ToursSetting FastAddress with Alternative Protocols Using an American Dynamics ControllerAlternative Control Protocols Exit Command Lock Enter FastAddressFastAddress 2Using a Pelco Controller New Fast Address Saved Setup MenuSetting FastAddress with a Pelco Keyboard Pelco Protocol Mode Hardware ConfigurationPelco Keyboard Commands Keyboard Command User Action Description PatternAux On / Aux Off Aux OnSpecial Preset Commands Preset Command DescriptionPreset Initiates Preset TourPelco On-Screen Menus Command Lock locked Pelco menu Bosch menu Setup MenuBosch Menu locked PTZ Setup unlocked Camera Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Advanced Features Alarm RulesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Example 3 Advanced Alarm Rule using AutoTrack Click the Online Config button and then expand AlarmClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Settings and Recommendations AutoTrack OperationAutoTrack Optimization Mount/Mounting Surface StabilityField of View Unwanted MotionSetting AutoTrack Optimization Parameters Virtual MaskingPrivacy Masking Consistent Light ConditionsPreset positions 90 through Motion Detection with Region of InterestImage Stabilization 7Pre-position TourSetting the Azimuth Zero Point 8Azimuth, Elevation, and Compass DirectionsAzimuth Range Compass Direction AutoHome Recalibration Commands and Settings Function Command Description Key NumberDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayUsing the AutoHome Recalibration Preset or Recorded TourSetting Values AutoHome Recalibration OperationTroubleshooting Guide If O.K., then If using a non-Bosch power supplyIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlIf amber LED does not light when given PTZ commands, then Cannot access userSettings No camera controlSetting FastAddress Does not switch If O.K., then Automatically whenWith an American Dynamics KeyboardInside of Outdoor Low Voltage flashingOn monitor display 2VG5 Series AutoDome Audio Audio Connections with an VG5 600 Series AutoDomeProblem Solution No Audio Problem Solution If O.K., then Poor AudioUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Appendix FastAddress Conversions BlockGroup Index NumericsCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc