Bosch Appliances VG5 600 user manual Example 2 Advanced Alarm Rule

Page 45

AutoDome 600 Series Analog PTZ Camera

Advanced Features en 45

 

 

4.Set up the Alarm Rule (for this example use Rule 1). Select the Inputs from the Rule Setup menu:

a.Select Rule 1.

b.Set the first input to Alarm Input 1.

5.Select the outputs:

a.Set the first output to OSD.

b.Set the second output to Shot 7.

c.Set the third output to Transmit.

6.Enable the rule:

– Highlight Enabled and select YES.

Example 2: Advanced Alarm Rule

Scenario: A VG5 AutoDome located at an airport is set to AutoPan Between Limits from the parking garage to the airport terminal. The gate entering the airport has an alarm contact connected to the AutoDome, and the perimeter fence in the area of the gate has an infrared (IR) motion detection sensor connected to the AutoDome.

When both the gate contact and motion detector alarms are activated at the same time, we want the alarm rule to:

1.Flash an OSD message (***ALARM 2***) on the monitor.

2.Stop the AutoPan and move the camera to a saved position (Shot 5) viewing the fence.

3.Turn on AutoTrack.

4.Transmit a Bilinx signal to the head end system to trigger an alarm response.

The sequence to program this alarm rule example is as follows:

1.Wire and set the alarm Input(s).

a.Wire the motion detector to Input 1. (This circuit is normally open.)

b.Wire the gate alarm contact to Input 5. (This circuit is normally closed.)

NOTICE!

For instruction on wiring alarm and relay connections, see the AutoDome Modular Camera System Installation Manual.

2.From the Inputs Setup menu:

a.Ensure Input 1 (the motion detector) is set to N.O. (This setting is the default for Input 1.)

b.Ensure Input 5 (the gate contact) is set to N.C.

3.Set the alarm Outputs from the Outputs Setup menu:

a.Set Output 5 to OSD.

b.Set Output 6 to Transmit.

c.Set Output 7 to Shot 5.

d.Set Output 8 to AutoTrack.

4.Set up the Alarm Rule (for this example use Rule 2). Select the alarm Inputs:

a.From the Rule Setup menu select Rule 2.

b.Set the first input to Alarm Input 1. (The motion detector.)

c.Set the second input to Alarm Input 5. (The gate alarm contact.)

5.Select the alarm Outputs:

a.Set the first output to OSD.

b.Set the second output to Shot 5 viewing the fence.

c.Set the third output to AutoTrack and select Latched.

d.Set the fourth output to Transmit (a Bilinx signal to the headend).

6.Enable the alarm Rule:

– Highlight Enabled and select YES.

Bosch Security Systems, Inc.

User Manual

F.01U.270.005 2.0 2012.06

Image 45
Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Keyboard Commands by Number Advanced Features Bosch Menu locked PTZ Setup unlocked Other MenusTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexGetting Started Powering OnEstablishing AutoDome Control For each of the system componentsKeyboard Commands Basic Keyboard OperationLCD FastAddress Setting the Camera AddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSpecial Passwords Setting PasswordsPassword Security Level To set or change a password locked commandTo open the main Setup Menu locked command Setup MenuSetup Menu On-Screen Display Menu NavigationCamera Setup Menu Auto ATWInternal OFFPAL Lens SetupExit Auto Focus Auto IrisSpot PTZ Setup MenuConstant FastNormal Momentary Display Setup MenuSector 1-16 Press Focus/Iris to blank or Edit Scene Title to accessPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Inputs Setup Alarm I/O SetupInputs NoneOutputs Setup Outputs Setup MenuAlarm Relay OutputsRule Setup Menu Rule SetupRule None Advanced Feature Setup Menu Advanced Feature SetupLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Common AutoDome User Commands unlocked Setting AutoPan Mode2Setting Preset Shots Specifying a Shot or a Sector Title 4Configuring Preposition ToursTo start Preposition Tour To stop a Preposition Tour6Recording Tours 5Programming the Inactivity OperationSetting FastAddress with Alternative Protocols Using an American Dynamics ControllerAlternative Control Protocols Enter FastAddress Exit Command LockFastAddress 2Using a Pelco Controller New Fast Address Saved Setup MenuSetting FastAddress with a Pelco Keyboard Hardware Configuration Pelco Protocol ModeKeyboard Command User Action Description Pattern Pelco Keyboard CommandsAux On / Aux Off Aux OnPreset Command Description Special Preset CommandsPreset Initiates Preset TourPelco On-Screen Menus Command Lock locked Pelco menu Bosch menu Setup MenuBosch Menu locked Camera Setup unlocked PTZ Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Alarm Rules Advanced FeaturesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Click the Online Config button and then expand Alarm Example 3 Advanced Alarm Rule using AutoTrackClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Operation AutoTrack Settings and RecommendationsMount/Mounting Surface Stability AutoTrack OptimizationField of View Unwanted MotionVirtual Masking Setting AutoTrack Optimization ParametersPrivacy Masking Consistent Light ConditionsMotion Detection with Region of Interest Preset positions 90 throughImage Stabilization 7Pre-position TourSetting the Azimuth Zero Point 8Azimuth, Elevation, and Compass DirectionsAzimuth Range Compass Direction Function Command Description Key Number AutoHome Recalibration Commands and SettingsDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayPreset or Recorded Tour Using the AutoHome RecalibrationSetting Values AutoHome Recalibration OperationIf O.K., then If using a non-Bosch power supply Troubleshooting GuideIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlCannot access user If amber LED does not light when given PTZ commands, thenSettings No camera controlDoes not switch If O.K., then Automatically when Setting FastAddressWith an American Dynamics KeyboardInside of Outdoor Low Voltage flashingOn monitor display Audio Connections with an VG5 600 Series AutoDome 2VG5 Series AutoDome AudioProblem Solution No Audio Poor Audio Problem Solution If O.K., thenUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Appendix FastAddress Conversions BlockGroup Numerics IndexCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc