Bosch Appliances VG5 600 user manual Inside of Outdoor, Low Voltage flashing, On monitor display

Page 58

58 en Troubleshooting GuideAutoDome 600 Series Analog PTZ Camera

Inside of Outdoor	– Check the status of the Heater Module (ON-66-ENTER).
Pendant bubble is	If status reports Heater No Power, then:
foggy	– Turn off the power to the AutoDome.
	– Check the FX103 fuse in the Power Supply Box for power (24 V) to the heater module.
	If O.K., then:
	– Check all wiring and connector pins to the heater module.

Low Voltage flashing	– If using a non-Bosch power supply, confirm that it meets the Bosch AutoDome power
on monitor display	ratings. See the AutoDome Datasheet for specifications.
	If O.K., then:
	– Check the mains input line voltage.
	If O.K., then:
	– Check that the maximum wire length from the power supply has not been exceeded.
	See the VG5 AutoDome Installation Manual.
	If O.K., then:
	– Measure the AC voltage input to the camera while power is applied to the camera. The
	voltage must be ≥ 21 VAC to stop the message.

F.01U.270.005 2.0 2012.06

User Manual

Bosch Security Systems, Inc.

Image 58

Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Troubleshooting Guide Bosch Menu locked PTZ Setup unlocked Other MenusKeyboard Commands by Number Advanced Features User Command Table Appendix FastAddress Conversions IndexEstablishing AutoDome Control Powering OnGetting Started For each of the system componentsBasic Keyboard Operation Keyboard CommandsLCD To set an address for a camera without an address Setting the Camera AddressFastAddress To change or clear an address for a camera with an addressPassword Security Level Setting PasswordsSpecial Passwords To set or change a password locked commandSetup Menu Setup MenuTo open the main Setup Menu locked command On-Screen Display Menu NavigationCamera Setup Menu Internal ATWAuto OFFExit Auto Focus Lens SetupPAL Auto IrisConstant PTZ Setup MenuSpot FastNormal Display Setup Menu MomentaryPrivacy Masking Edit Scene Title to accessSector 1-16 Press Focus/Iris to blank or Edit Sector TitleCommunication Setup Menu Inputs Alarm I/O SetupAlarm I/O Setup Inputs Setup NoneAlarm Relay Outputs Setup MenuOutputs Setup OutputsRule Setup Rule Setup MenuRule None Advanced Feature Setup Advanced Feature Setup MenuLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Setting AutoPan Mode Common AutoDome User Commands unlocked2Setting Preset Shots To start Preposition Tour 4Configuring Preposition ToursSpecifying a Shot or a Sector Title To stop a Preposition Tour5Programming the Inactivity Operation 6Recording ToursUsing an American Dynamics Controller Setting FastAddress with Alternative ProtocolsAlternative Control Protocols Exit Command Lock Enter FastAddressFastAddress New Fast Address Saved Setup Menu 2Using a Pelco ControllerSetting FastAddress with a Pelco Keyboard Pelco Protocol Mode Hardware ConfigurationAux On / Aux Off Pelco Keyboard CommandsKeyboard Command User Action Description Pattern Aux OnPreset Special Preset CommandsPreset Command Description Initiates Preset TourPelco On-Screen Menus Pelco menu Bosch menu Setup Menu Command Lock lockedBosch Menu locked Pelco Camera Setup Menu provides access to camera settings PTZ Setup unlockedCamera Setup unlocked OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Controlling Alarm Rules Advanced FeaturesAlarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Click Output Option Example 3 Advanced Alarm Rule using AutoTrackClick the Online Config button and then expand Alarm Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Settings and Recommendations AutoTrack OperationField of View AutoTrack OptimizationMount/Mounting Surface Stability Unwanted MotionPrivacy Masking Setting AutoTrack Optimization ParametersVirtual Masking Consistent Light ConditionsImage Stabilization Preset positions 90 throughMotion Detection with Region of Interest 7Pre-position Tour8Azimuth, Elevation, and Compass Directions Setting the Azimuth Zero PointAzimuth Range Compass Direction Displaying Azimuth, Elevation, and Compass Headings AutoHome Recalibration Commands and SettingsFunction Command Description Key Number Readings and the compass heading in the following waySetting Values Using the AutoHome RecalibrationPreset or Recorded Tour AutoHome Recalibration Operation If O.K., then If there is power to the AutoDome, then Troubleshooting Guide If O.K., then If using a non-Bosch power supply VG5 AutoDome Operation and ControlSettings If amber LED does not light when given PTZ commands, thenCannot access user No camera controlWith an American Setting FastAddressDoes not switch If O.K., then Automatically when Dynamics KeyboardLow Voltage flashing Inside of OutdoorOn monitor display 2VG5 Series AutoDome Audio Audio Connections with an VG5 600 Series AutoDomeProblem Solution No Audio Problem Solution If O.K., then Poor AudioUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Block Appendix FastAddress ConversionsGroup Index NumericsCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc