Bosch Appliances VG5 600 Motion Detection with Region of Interest, Preset positions 90 through

Page 51

AutoDome 600 Series Analog PTZ CameraAdvanced Features en 51

7.5

Motion Detection with Region of Interest

 

(Preset positions 90 through 99)

With the VG5 Series AutoDome, the motion detection software can be configured to create a Region of Interest within multiple preset positions or scenes. It can take advantage of Virtual Masking to ignore motion in predefined areas. Motion Detection can also be used as an Alarm Rule input.

Preset positions 90 through 99 are reserved for programming motion detection scenes.

NOTICE!

Motion Detection always takes precedence over AutoTrack object tracking.

To set up a scene with Motion Detection:

1.Choose an unused Preset position from 90 to 99. For this example use Preset scene 95.

2.Enter the keyboard command SET-95-ENTER.

3.Select YES at the Apply Motion Detection? prompt. (If NO is selected, the Preset scene does not activate Motion Detection.)

4.Select YES at the Apply Region of Interest? prompt. (If NO is selected, the entire scene is used for Motion Detection.)

5.Follow the on-screen menu instructions to construct the shape of the screen area you want to detect motion within.

NOTICE! Up to five (5) anchor points can be used to form the area which you want to detect motion within. Motion Detection is not activated until the Preset scene is recalled. The Motion Detection icon "M" appears in the upper left-hand corner of the display.

7.6

Image Stabilization

Image Stabilization becomes increasingly important as zoom ranges are extended. The advanced image stabilization algorithms of the VG5 Series AutoDome eliminate camera shake for exceptional image clarity. Bosch achieves this clarity without reducing camera sensitivity or picture quality.

To configure image stabilization, open the Main menu, select the Advanced menu, and then select Stabilization to turn on the feature.

In Pelco Mode open the Main menu, select the Advanced menu, and then select Stabilization to turn on the feature.

7.7Pre-position Tour

The VG5 Series AutoDome features (2) preset tours. Each preset scene is saved for playback later.

Tour 1 is a standard tour that only recalls the scenes in the exact sequence they were shot. Scenes can be added or deleted on the tour, but the sequence cannot be changed. To add or remove scenes on Tour 1 enter the keyboard command SHOT-900-ENTERand follow the on- screen instructions.

Tour 2 is a customizable tour that allows you to rearrange the sequence of scenes on the tour by inserting and deleting scenes. To enter the Edit Tour 2 menu, enter the keyboard command SET-900-ENTERand follow the on-screen instructions.

Bosch Security Systems, Inc.

User Manual

F.01U.270.005 2.0 2012.06

Image 51
Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents User Command Table Appendix FastAddress Conversions Index Bosch Menu locked PTZ Setup unlocked Other MenusKeyboard Commands by Number Advanced Features Troubleshooting GuideFor each of the system components Powering OnGetting Started Establishing AutoDome ControlKeyboard Commands Basic Keyboard OperationLCD To change or clear an address for a camera with an address Setting the Camera AddressFastAddress To set an address for a camera without an addressTo set or change a password locked command Setting PasswordsSpecial Passwords Password Security LevelOn-Screen Display Menu Navigation Setup MenuTo open the main Setup Menu locked command Setup MenuCamera Setup Menu OFF ATWAuto InternalAuto Iris Lens SetupPAL Exit Auto FocusFast PTZ Setup MenuSpot ConstantNormal Momentary Display Setup MenuEdit Sector Title Edit Scene Title to accessSector 1-16 Press Focus/Iris to blank or Privacy MaskingCommunication Setup Menu None Alarm I/O SetupAlarm I/O Setup Inputs Setup InputsOutputs Outputs Setup MenuOutputs Setup Alarm RelayRule Setup Menu Rule SetupRule None Advanced Feature Setup Menu Advanced Feature SetupLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Common AutoDome User Commands unlocked Setting AutoPan Mode2Setting Preset Shots To stop a Preposition Tour 4Configuring Preposition ToursSpecifying a Shot or a Sector Title To start Preposition Tour6Recording Tours 5Programming the Inactivity OperationSetting FastAddress with Alternative Protocols Using an American Dynamics ControllerAlternative Control Protocols Enter FastAddress Exit Command LockFastAddress 2Using a Pelco Controller New Fast Address Saved Setup MenuSetting FastAddress with a Pelco Keyboard Hardware Configuration Pelco Protocol ModeAux On Pelco Keyboard CommandsKeyboard Command User Action Description Pattern Aux On / Aux OffInitiates Preset Tour Special Preset CommandsPreset Command Description PresetPelco On-Screen Menus Command Lock locked Pelco menu Bosch menu Setup MenuBosch Menu locked Outdoor PTZ Setup unlockedCamera Setup unlocked Pelco Camera Setup Menu provides access to camera settingsOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Alarm Rule Examples Advanced FeaturesAlarm Rules Controlling Alarm RulesExample 2 Advanced Alarm Rule Select Shot from the Type drop-down list Example 3 Advanced Alarm Rule using AutoTrackClick the Online Config button and then expand Alarm Click Output OptionOutput Option 6 Configuration AutoTrack Operation AutoTrack Settings and RecommendationsUnwanted Motion AutoTrack OptimizationMount/Mounting Surface Stability Field of ViewConsistent Light Conditions Setting AutoTrack Optimization ParametersVirtual Masking Privacy Masking7Pre-position Tour Preset positions 90 throughMotion Detection with Region of Interest Image StabilizationSetting the Azimuth Zero Point 8Azimuth, Elevation, and Compass DirectionsAzimuth Range Compass Direction Readings and the compass heading in the following way AutoHome Recalibration Commands and SettingsFunction Command Description Key Number Displaying Azimuth, Elevation, and Compass HeadingsAutoHome Recalibration Operation Using the AutoHome RecalibrationPreset or Recorded Tour Setting ValuesVG5 AutoDome Operation and Control Troubleshooting GuideIf O.K., then If using a non-Bosch power supply If O.K., then If there is power to the AutoDome, thenNo camera control If amber LED does not light when given PTZ commands, thenCannot access user SettingsDynamics Keyboard Setting FastAddressDoes not switch If O.K., then Automatically when With an AmericanInside of Outdoor Low Voltage flashingOn monitor display Audio Connections with an VG5 600 Series AutoDome 2VG5 Series AutoDome AudioProblem Solution No Audio Poor Audio Problem Solution If O.K., thenUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Appendix FastAddress Conversions BlockGroup Numerics IndexCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc