Bosch Appliances VG5 600 Advanced Features, Controlling Alarm Rules, Alarm Rule Examples

Page 44

44 en Advanced FeaturesAutoDome 600 Series Analog PTZ Camera

7

Advanced Features

 

This chapter details the advanced features of the VG5 AutoDome Camera.

7.1

Alarm Rules

 

The AutoDome features a powerful alarm rule engine. In its simplest form, an alarm rule

 

defines those inputs that activate specific outputs. In its more complex form, a rule can be

 

programmed to take any combination of inputs and keyboard commands to perform a dome

 

function. There are numerous combinations of alarm inputs and outputs that can be

 

programmed into twelve alarm rules.

7.1.1

Controlling Alarm Rules

 

The AUX 69 command allows a user to enable or disable all alarm rules. By default, alarm rules

 

are enabled until the OFF-69-ENTER command is issued from a keyboard (there is no

 

corresponding menu item for this command). Disabling alarms rules does not erase the rule,

 

the AutoDome preserves the user-defined settings and the rule data is restored when the ON-

 

69-ENTER command is issued.

 

The OFF-69-ENTER command performs the following actions:

 

–

Disables all alarm rules

 

–

Displays the message “Ack and Reset Alarms” if an alarm-rule triggered alarm is active

 

 

when the AutoDome receives the disable command. You must acknowledge the alarm

 

 

before the rule is disabled.

 

–

Prevents the modification of an alarm rule while disabled.

7.1.2

Alarm Rule Examples

 

Following are three examples for setting up alarm rules. The first example is a basic alarm

 

rule, and the second and third examples are more complex.

 

Example 1: Basic Alarm Rule

 

Scenario: We want a door alarm contact to:

 

1.

Flash an OSD message (***ALARM 1***) on the display when the alarm is triggered.

 

2.

Move the AutoDome camera to a saved position. (For this example Shot 7.)

 

3.

Transmit a Bilinx signal over the coax cable to the headend system, such as an Allegiant,

 

 

to trigger an alarm response.

 

The sequence to program the above alarm rule example is as follows:

 

1.

Wire the door contact to Input 1 in the AutoDome. This circuit is normally open.

 

2.

Define the Alarm Input(s)

 

 

– From the Inputs Setup menu, ensure that Alarm Input 1 is set to N.O. (This is the

 

 

 

default setting for Input 1.)

 

 

 

NOTICE! For instruction on wiring alarm and relay connections, see the VG5 AutoDome

 

Installation Manual.

 

 

 

 

3.

Define the Alarm Outputs from the Outputs Setup menu:

 

 

a.

Ensure Output 5 is set to OSD. (This is the default setting for Output 5.)

 

 

b. Set Output 6 to Shot 7.

 

 

c.

Set Output 7 to Transmit (a Bilinx signal to the head end).

F.01U.270.005 2.0 2012.06

User Manual

Bosch Security Systems, Inc.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Bosch Menu locked PTZ Setup unlocked Other Menus Keyboard Commands by Number Advanced FeaturesTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexPowering On Getting StartedEstablishing AutoDome Control For each of the system componentsLCD Keyboard CommandsBasic Keyboard Operation Setting the Camera Address FastAddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSetting Passwords Special PasswordsPassword Security Level To set or change a password locked commandSetup Menu To open the main Setup Menu locked commandSetup Menu On-Screen Display Menu NavigationCamera Setup Menu ATW AutoInternal OFFLens Setup PALExit Auto Focus Auto IrisPTZ Setup Menu SpotConstant FastNormal Display Setup Menu MomentaryEdit Scene Title to access Sector 1-16 Press Focus/Iris to blank orPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Alarm I/O Setup Inputs SetupInputs NoneOutputs Setup Menu Outputs SetupAlarm Relay OutputsRule Rule Setup MenuRule Setup None Language Menu Advanced Feature Setup MenuAdvanced Feature Setup Diagnostics Menu Bist 11.1 Alarm Status Submenu 2Setting Preset Shots Common AutoDome User Commands unlockedSetting AutoPan Mode 4Configuring Preposition Tours Specifying a Shot or a Sector TitleTo start Preposition Tour To stop a Preposition Tour5Programming the Inactivity Operation 6Recording ToursAlternative Control Protocols Setting FastAddress with Alternative ProtocolsUsing an American Dynamics Controller Exit Command Lock Enter FastAddressFastAddress Setting FastAddress with a Pelco Keyboard 2Using a Pelco ControllerNew Fast Address Saved Setup Menu Pelco Protocol Mode Hardware ConfigurationPelco Keyboard Commands Keyboard Command User Action Description PatternAux On / Aux Off Aux OnSpecial Preset Commands Preset Command DescriptionPreset Initiates Preset TourPelco On-Screen Menus Bosch Menu locked Command Lock lockedPelco menu Bosch menu Setup Menu PTZ Setup unlocked Camera Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Advanced Features Alarm RulesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Example 3 Advanced Alarm Rule using AutoTrack Click the Online Config button and then expand AlarmClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Settings and Recommendations AutoTrack OperationAutoTrack Optimization Mount/Mounting Surface StabilityField of View Unwanted MotionSetting AutoTrack Optimization Parameters Virtual MaskingPrivacy Masking Consistent Light ConditionsPreset positions 90 through Motion Detection with Region of InterestImage Stabilization 7Pre-position TourAzimuth Range Compass Direction Setting the Azimuth Zero Point8Azimuth, Elevation, and Compass Directions AutoHome Recalibration Commands and Settings Function Command Description Key NumberDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayUsing the AutoHome Recalibration Preset or Recorded TourSetting Values AutoHome Recalibration OperationTroubleshooting Guide If O.K., then If using a non-Bosch power supplyIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlIf amber LED does not light when given PTZ commands, then Cannot access userSettings No camera controlSetting FastAddress Does not switch If O.K., then Automatically whenWith an American Dynamics KeyboardOn monitor display Inside of OutdoorLow Voltage flashing 2VG5 Series AutoDome Audio Audio Connections with an VG5 600 Series AutoDomeProblem Solution No Audio Problem Solution If O.K., then Poor AudioUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Group Appendix FastAddress ConversionsBlock Index NumericsCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc
Top Page Image Contents