Bosch Appliances VG5 600 Setting FastAddress, With an American, Dynamics Keyboard, Colors are not

Page 57

AutoDome 600 Series Analog PTZ CameraTroubleshooting Guide en 57

Setting FastAddress	The FastAddress value must match the Unique Identifier for the AutoDome. To set the
with an American	FastAddress on an American Dynamics keyboard refer to Section 4.1 Setting FastAddress
Dynamics Keyboard	with Alternative Protocols, page 29.

Picture is dark	– Check that the Gain Control is set to AUTO (ON-43-ENTER).
	If O.K., then:
	– Check that the Auto Iris Level is set to the appropriate level (ON-11-ENTER).
	If O.K., then:
	– Check that the video coax is terminated with 75 Ω only at the head end. (Double
	termination causes dark video.)
	If O.K., then:
	– Go to the Camera Setup Menu and increase the Pre-Compensation setting.
	If O.K., then:
	– Check that the camera lens cover is removed.
	If O.K., then:
	– Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
	Installation Manual.
	If O.K., then:
	– Restore all camera settings (ON-40-ENTER).

Colors are not	– Reset the White Balance to the appropriate selection (ON-30-ENTER).
correct	If O.K., then:
	– Go to the Camera Setup Menu and increase the Pre-Compensation setting.
	If O.K., then:
	– Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
	Installation Manual.
	If O.K., then:
	– Restore the default settings (ON-40-ENTER).

Background is too	– Turn on backlight compensation (ON-20-ENTER).
bright to see subject

Video is rolling,	– Ensure that the Synch Mode is set to Internal (OFF-42-ENTER).
noisy or distorted	If O.K., then:
	– Check that the maximum coax distance has not been exceeded. See the VG5 AutoDome
	Installation Manual.
	If O.K., then:
	– Check the integrity of all BNC connectors and splices.
	Note: Connecting a network cable to the interface board of a non-IP AutoDome causes
	video distortion.
	– Remove the network cable from the interface board RJ-45 connector.
	If O.K., then:
	– Contact Bosch Technical Support.

Day/Night camera	– Check that the Day/Night mode is set to AUTO (ON-56-ENTER).
does not switch	If O.K., then:
automatically when	– Set Gain Control to AUTO (ON-43-ENTER).
image is dark

Bosch Security Systems, Inc.

User Manual

F.01U.270.005 2.0 2012.06

Image 57

Contents AutoDome 600 Series Analog PTZ Cam- era Page Table of Contents Keyboard Commands by Number Advanced Features Bosch Menu locked PTZ Setup unlocked Other MenusTroubleshooting Guide User Command Table Appendix FastAddress Conversions IndexGetting Started Powering OnEstablishing AutoDome Control For each of the system componentsKeyboard Commands Basic Keyboard OperationLCD FastAddress Setting the Camera AddressTo set an address for a camera without an address To change or clear an address for a camera with an addressSpecial Passwords Setting PasswordsPassword Security Level To set or change a password locked commandTo open the main Setup Menu locked command Setup MenuSetup Menu On-Screen Display Menu NavigationCamera Setup Menu Auto ATWInternal OFFPAL Lens SetupExit Auto Focus Auto IrisSpot PTZ Setup MenuConstant FastNormal Momentary Display Setup MenuSector 1-16 Press Focus/Iris to blank or Edit Scene Title to accessPrivacy Masking Edit Sector TitleCommunication Setup Menu Alarm I/O Setup Inputs Setup Alarm I/O SetupInputs NoneOutputs Setup Outputs Setup MenuAlarm Relay OutputsRule Setup Menu Rule SetupRule None Advanced Feature Setup Menu Advanced Feature SetupLanguage Menu Diagnostics Menu Bist 11.1 Alarm Status Submenu Common AutoDome User Commands unlocked Setting AutoPan Mode2Setting Preset Shots Specifying a Shot or a Sector Title 4Configuring Preposition ToursTo start Preposition Tour To stop a Preposition Tour6Recording Tours 5Programming the Inactivity OperationSetting FastAddress with Alternative Protocols Using an American Dynamics ControllerAlternative Control Protocols Enter FastAddress Exit Command LockFastAddress 2Using a Pelco Controller New Fast Address Saved Setup MenuSetting FastAddress with a Pelco Keyboard Hardware Configuration Pelco Protocol ModeKeyboard Command User Action Description Pattern Pelco Keyboard CommandsAux On / Aux Off Aux OnPreset Command Description Special Preset CommandsPreset Initiates Preset TourPelco On-Screen Menus Command Lock locked Pelco menu Bosch menu Setup MenuBosch Menu locked Camera Setup unlocked PTZ Setup unlockedPelco Camera Setup Menu provides access to camera settings OutdoorOther Menus Keyboard Commands by Number Zone Title Menu Enters Zone Title menu. Refer to Refer to .8 Azimuth, Elevation, Compass Directions, Locked Function Comm Command Description Key Alarm Rules Advanced FeaturesControlling Alarm Rules Alarm Rule ExamplesExample 2 Advanced Alarm Rule Click the Online Config button and then expand Alarm Example 3 Advanced Alarm Rule using AutoTrackClick Output Option Select Shot from the Type drop-down listOutput Option 6 Configuration AutoTrack Operation AutoTrack Settings and RecommendationsMount/Mounting Surface Stability AutoTrack OptimizationField of View Unwanted MotionVirtual Masking Setting AutoTrack Optimization ParametersPrivacy Masking Consistent Light ConditionsMotion Detection with Region of Interest Preset positions 90 throughImage Stabilization 7Pre-position TourSetting the Azimuth Zero Point 8Azimuth, Elevation, and Compass DirectionsAzimuth Range Compass Direction Function Command Description Key Number AutoHome Recalibration Commands and SettingsDisplaying Azimuth, Elevation, and Compass Headings Readings and the compass heading in the following wayPreset or Recorded Tour Using the AutoHome RecalibrationSetting Values AutoHome Recalibration OperationIf O.K., then If using a non-Bosch power supply Troubleshooting GuideIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlCannot access user If amber LED does not light when given PTZ commands, thenSettings No camera controlDoes not switch If O.K., then Automatically when Setting FastAddressWith an American Dynamics KeyboardInside of Outdoor Low Voltage flashingOn monitor display Audio Connections with an VG5 600 Series AutoDome 2VG5 Series AutoDome AudioProblem Solution No Audio Poor Audio Problem Solution If O.K., thenUser Command Table AutoDome 600 Series Analog PTZ Camera User Command Table en Appendix FastAddress Conversions BlockGroup Numerics IndexCommand lock 36 Command Lock menu 37 commands Setup Custom tour PTZ En Index AutoDome 600 Series Analog PTZ Camera Page Page Page Bosch Security Systems, Inc