Panasonic WV-SP105E, WV-SP102E Action at an alarm occurrence, Alarm type

Page 10

Action at an alarm occurrence

The alarm action (camera action at an alarm occurrence) will be performed when the following alarms occur.

Alarm type

VMD alarm:

When motion is detected in the set VMD area, the alarm action will be performed.

 

* VMD stands for "Video Motion Detection".

Command alarm:

When a Panasonic alarm protocol is received from the connected device via a network, the

 

alarm action will be performed.

Action at an alarm occurrence

Display the alarm occurrence indication button on the "Live" page. (Page 8)

The alarm occurrence indication button will be displayed on the "Live" page at an alarm occurrence.

Important:

When "Polling(30sec)" is selected for "Alarm status update mode" (page 18), the alarm occurrence indication button will be refreshed in 30 second intervals. For this reason, it may take a maximum of 30 seconds until the alarm occurrence indication button is displayed on the "Live" page at an alarm occurrence.

Transmit an image onto a server automatically

An alarm image can be transmitted at an alarm occurrence to the server designated in advance. The settings required to transmit an alarm image to a server can be configured in the "Alarm image" section on the [Alarm] tab of the "Alarm" page (page 32) and the [FTP] tab of the "Server" page (page 41).

Notify of alarm occurrences by e-mail

Alarm mail (alarm occurrence notification) can be sent at an alarm occurrence to the e-mail addresses registered in advance. Up to 4 addresses can be registered as recipients of the alarm mail. An alarm image (still picture) can be sent with the alarm mail as an attached file. The settings for alarm mail can be configured in the "Mail notification" section on the [Notification] tab of the "Alarm" page (page 36) and the [Mail] tab of the "Server" page (page 41).

Notify of alarm occurrences to the designated IP addresses (Panasonic alarm protocol notification)

This function is available only when a Panasonic device, such as the network disk recorder, is connected to the system. When "On" is selected for "Panasonic alarm protocol notification", the connected Panasonic device will be notified that the camera is in the alarm state. The settings for Panasonic alarm protocol can be configured in the Panasonic alarm protocol section of the [Notification] tab of the "Alarm" page. (Page 37)

10

Image 10
Contents Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102E Operating InstructionsContents Trademarks and registered trademarks PrefaceAbout notations AbbreviationsViewer software Monitor images on a PC Example of IPv4 accessExample of IPv6 access Monitor images from a single cameraRefresh interval of Jpeg images About the Live Brightness buttons*2 Alarm occurrence indication button*2Zoom buttons + brighter button Image will be brighter Camera titleMonitor images from multiple cameras Action at an alarm occurrence Action at an alarm occurrenceAlarm type Notify of alarm occurrences by e-mailTransmit images onto an FTP server About the network security Equipped security functionsDisplay the setup menu from a PC How to display the setup menuHow to operate the setup menu About the setup menu window 0Schedule button 1Maintenance button4Setup 2Help buttonConfigure the basic settings Basic Link indicator orange Default On Link/Access indicatorDefault On Power indicator green Access indicator GreenAspect ratio Configure the settings relating to Jpeg images JPEG/H.264Default 1280x960*1 Refresh interval JpegConfigure the settings relating to H.264 images JPEG/H.264 264 1 · H.264Image capture size Default 30fpsDefault Normal Transmission priorityRefresh interval Default Multicast TTL/HOPLimit*2Available value 1 Default Transmission typeExtra zoom SP105 Image adjustPrivacy zone Adaptive black stretch Default Off Mask areaBack light compensationBLC Simple black & white mode Light control modeDefault OnHigh Auto slow shutter Default Off White balanceDefault High Chroma gain level Default ATW1Default Blue gain Default Pedestal levelSet mask areas + button Reset buttonExtra zoom − buttonArea Default Off Setup buttonDisplay type Example of entry IP addressAvailable number of characters 1 128 characters Configure the settings relating to the alarm action Alarm Configure the alarm settings AlarmAlarm Configure the settings relating to the alarm image Alarm Alarm imageConfigure the VMD settings VMD area Light detection control VMD information additionInformation addition Set the VMD areas VMD area Mail notification Destination of notificationAvailable range 1 Default Retry times Panasonic alarm protocol notificationPanasonic alarm protocol Destination portUser auth Password Retype passwordAccess level Available number of characters 4 32 charactersHost check Default Off IP addressHost auth Activation Default 1280×960*1 VGA*2Priority stream Destination IP addressConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Default Time adjustment interval Configure the settings relating to the NTP server NTPTime adjustment Default 1hConfigure the network settings Network Configure the network settings NetworkIPv4 network IPv6 network CommonEasy IP Setup accommodate period Default 20minAccess interval Configure the settings relating to Ddns DdnsDefault Off Host name Available number of characters 1 64 charactersConfigure the settings relating to Snmp Snmp FTP periodic image transmission Default Off Directory nameDefault 1s FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Check the system log System log Maintenance of the camera MaintenanceError description Time & dateUpgrade the firmware Upgrade Reset to the default and load the default Html files Reset the settings/Reboot the camera Default resetReboot Viewing Help Displaying the Help screenAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to loginCannot access from the web TroubleshootingBrowser No image is displayed Image is not being refreshed Alarm occurrence indicationNo indicator lights No image is displayed or tooWhen displaying H.264 images Pop-up blocked. To see this Following message is disPlayed on the information bar Pop-up or additional optionsPanasonic Canada Inc