Panasonic WV-SP105E, WV-SP102E operating instructions Viewer software

Page 4

Viewer software

•It is necessary to install the viewer software "Network Camera View 4S" to display images on a PC. This soft- ware can be installed directly from the camera or by double clicking "nwcv4Ssetup.exe" on the CD-ROM pro- vided, and then following the on-screen instructions.

Important:

•The default setting of "Automatic installation of Viewer software" is "On". Follow the instructions on page 63 when the message is dis- played on the information bar of the browser.

•When the "Live" page is displayed for the first time, the install wiz- ard of the ActiveX control required to display images from the cam- era will be displayed. Follow the instructions of the wizard.

•When the install wizard is displayed again even after completing the installation of the ActiveX, restart the PC.

•The viewer software used on each PC should be licensed individu- ally. The number of installations of the viewer software from the camera can be checked on the [Upgrade] tab of the "Maintenance" page (☞ page 54). Refer to your dealer for the software licensing.

4

Image 4

Contents Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102E Operating InstructionsContents Preface About notationsTrademarks and registered trademarks AbbreviationsViewer software Example of IPv4 access Example of IPv6 accessMonitor images on a PC Monitor images from a single cameraRefresh interval of Jpeg images About the Live Alarm occurrence indication button*2 Zoom buttonsBrightness buttons*2 + brighter button Image will be brighter Camera titleMonitor images from multiple cameras Action at an alarm occurrence Alarm typeAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server About the network security Equipped security functionsDisplay the setup menu from a PC How to display the setup menuHow to operate the setup menu About the setup menu window 1Maintenance button 4Setup0Schedule button 2Help buttonConfigure the basic settings Basic Default On Link/Access indicator Default On Power indicator greenLink indicator orange Access indicator GreenConfigure the settings relating to Jpeg images JPEG/H.264 Default 1280x960*1Aspect ratio Refresh interval JpegConfigure the settings relating to H.264 images JPEG/H.264 264 1 · H.264Default 30fps Default NormalImage capture size Transmission priorityDefault Multicast TTL/HOPLimit*2 Available value 1 DefaultRefresh interval Transmission typeExtra zoom SP105 Image adjustPrivacy zone Adaptive black stretch Default Off Mask areaBack light compensationBLC Light control mode Default OnHigh Auto slow shutterSimple black & white mode Default Off White balanceDefault ATW1 Default Blue gainDefault High Chroma gain level Default Pedestal levelSet mask areas Reset button Extra zoom+ button − buttonArea Default Off Setup buttonDisplay type Example of entry IP addressAvailable number of characters 1 128 characters Configure the settings relating to the alarm action Alarm Configure the alarm settings AlarmAlarm Configure the settings relating to the alarm image Alarm Alarm imageConfigure the VMD settings VMD area Light detection control VMD information additionInformation addition Set the VMD areas VMD area Mail notification Destination of notificationPanasonic alarm protocol notification Panasonic alarm protocolAvailable range 1 Default Retry times Destination portPassword Retype password Access levelUser auth Available number of characters 4 32 charactersHost check Default Off IP addressHost auth Default 1280×960*1 VGA*2 Priority streamActivation Destination IP addressConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Configure the settings relating to the NTP server NTP Time adjustmentDefault Time adjustment interval Default 1hConfigure the network settings Network Configure the network settings NetworkIPv4 network IPv6 network CommonEasy IP Setup accommodate period Default 20minConfigure the settings relating to Ddns Ddns Default Off Host nameAccess interval Available number of characters 1 64 charactersConfigure the settings relating to Snmp Snmp Default Off Directory name Default 1sFTP periodic image transmission FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Maintenance of the camera Maintenance Error descriptionCheck the system log System log Time & dateUpgrade the firmware Upgrade Reset to the default and load the default Html files Reset the settings/Reboot the camera Default resetReboot Viewing Help Displaying the Help screenAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to loginCannot access from the web TroubleshootingBrowser No image is displayed Alarm occurrence indication No indicator lightsImage is not being refreshed No image is displayed or tooWhen displaying H.264 images Following message is dis Played on the information barPop-up blocked. To see this Pop-up or additional optionsPanasonic Canada Inc