Panasonic WV-SP102 Refresh interval, Transmission type, Unicast port1 Image*1, Multicast port*2

Page 22

Note:

When "Constant bit rate" is selected for "Recording priority", this setting is available.

[Refresh interval]

Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images.

If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264 to diminish image distortions. However, the refresh interval may be longer than the set value.

0.2s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s Default: 3s

[Transmission type]

Select the transmission type of H.264 images from the following.

Unicast port (AUTO): Up to 14 users can access a sin- gle camera concurrently. "Unicast port1(Image)" will automatically be selected when transmitting images from the camera. When it is unnecessary to fix the port number for H.264 image transmission such as when using in a particular LAN environment, it is recommended to select "Unicast port (AUTO)".

Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select "Unicast port1(Image)" manually to transmit images from the camera. It is possible to fix the port num- ber of the router used for H.264 image transmission via the Internet by setting "Unicast port (MANUAL)" (page 46). Refer to the operating instructions of the router in use.

Multicast: Unlimited number of users can access a sin- gle camera concurrently. Complete the entry field of "Multicast address", "Multicast port" and "Multicast TTL/HOPLimit" when transmitting H.264 images with multicast.

*Refer to page 6 for further information about the maximum concurrent access number.

Default: Unicast port (AUTO)

[Unicast port1 (Image)]*1

Enter the unicast port number (used to transmit images from the camera).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: H.264(1): 32004 H.264(2): 32014

[Multicast address]*2

Enter the multicast IP address.

Images will be transmitted to the designated IP address.

Available IPv4 address: 224.0.0.0 - 239.255.255.255

Available IPv6 address: Multicast address starting with "FF"

Default: H.264(1): 239.192.0.20

H.264(2): 239.192.0.21

Note:

Enter a multicast IP address after checking available multicast address.

[Multicast port]*2

Enter the multicast port number (used to transmit images from the camera).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: 37004

[Multicast TTL/HOPLimit]*2

Enter the multicast TTL/HOPLimit value.

Available value: 1 - 254

Default: 16

Important:

When transmitting an H.264 image via a network, the transmitted image sometimes may not be dis- played depending on the settings of a proxy server or a firewall. In this case, refer to the network administrator.

When two or more network interface cards are installed on the PC in use, the network interface card(s) not used for receiving images should be invalidated when displaying images using the multi- cast port.

*1 It is necessary to designate the unicast port number when "Unicast port (MANUAL)" is selected for "Transmission type".

*2 It is necessary to designate the multicast IP address when "Multicast" is selected for "Transmission type".

22

Image 22
Contents Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102E Operating InstructionsContents Trademarks and registered trademarks PrefaceAbout notations AbbreviationsViewer software Monitor images on a PC Example of IPv4 accessExample of IPv6 access Monitor images from a single cameraRefresh interval of Jpeg images About the Live Brightness buttons*2 Alarm occurrence indication button*2Zoom buttons + brighter button Image will be brighter Camera titleMonitor images from multiple cameras Action at an alarm occurrence Action at an alarm occurrenceAlarm type Notify of alarm occurrences by e-mailTransmit images onto an FTP server About the network security Equipped security functionsDisplay the setup menu from a PC How to display the setup menuHow to operate the setup menu About the setup menu window 0Schedule button 1Maintenance button4Setup 2Help buttonConfigure the basic settings Basic Link indicator orange Default On Link/Access indicatorDefault On Power indicator green Access indicator GreenAspect ratio Configure the settings relating to Jpeg images JPEG/H.264Default 1280x960*1 Refresh interval JpegConfigure the settings relating to H.264 images JPEG/H.264 264 1 · H.264Image capture size Default 30fpsDefault Normal Transmission priorityRefresh interval Default Multicast TTL/HOPLimit*2Available value 1 Default Transmission typeExtra zoom SP105 Image adjustPrivacy zone Adaptive black stretch Default Off Mask areaBack light compensationBLC Simple black & white mode Light control modeDefault OnHigh Auto slow shutter Default Off White balanceDefault High Chroma gain level Default ATW1Default Blue gain Default Pedestal levelSet mask areas + button Reset buttonExtra zoom − buttonArea Default Off Setup buttonDisplay type Example of entry IP addressAvailable number of characters 1 128 characters Configure the settings relating to the alarm action Alarm Configure the alarm settings AlarmAlarm Configure the settings relating to the alarm image Alarm Alarm imageConfigure the VMD settings VMD area Light detection control VMD information additionInformation addition Set the VMD areas VMD area Mail notification Destination of notificationAvailable range 1 Default Retry times Panasonic alarm protocol notificationPanasonic alarm protocol Destination portUser auth Password Retype passwordAccess level Available number of characters 4 32 charactersHost check Default Off IP addressHost auth Activation Default 1280×960*1 VGA*2Priority stream Destination IP addressConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Default Time adjustment interval Configure the settings relating to the NTP server NTPTime adjustment Default 1hConfigure the network settings Network Configure the network settings NetworkIPv4 network IPv6 network CommonEasy IP Setup accommodate period Default 20minAccess interval Configure the settings relating to Ddns DdnsDefault Off Host name Available number of characters 1 64 charactersConfigure the settings relating to Snmp Snmp FTP periodic image transmission Default Off Directory nameDefault 1s FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Check the system log System log Maintenance of the camera MaintenanceError description Time & dateUpgrade the firmware Upgrade Reset to the default and load the default Html files Reset the settings/Reboot the camera Default resetReboot Viewing Help Displaying the Help screenAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to loginCannot access from the web TroubleshootingBrowser No image is displayed Image is not being refreshed Alarm occurrence indicationNo indicator lights No image is displayed or tooWhen displaying H.264 images Pop-up blocked. To see this Following message is disPlayed on the information bar Pop-up or additional optionsPanasonic Canada Inc