Panasonic WV-SP102E Configure the settings relating to Jpeg images JPEG/H.264, Aspect ratio

Page 19

Configure the settings relating to images [Image]

The settings relating to JPEG and H.264 images such as the settings of image quality, etc. can be configured on this page.

The "Image" page has 2 tabs; the [JPEG/H.264] tab and the [Image/Privacy] tab.

Configure the settings relating to the aspect ratio [JPEG/H.264]

Click the [JPEG/H.24] tab on the "Image" page. (Pages 13 and 14: How to display/operate the setup menu)

[Aspect ratio]

Select "4:3" or "16:9" for the aspect ratio. Default: 4:3

Note:

i-PRO Series does not support aspect ratio of "16:9", if not specified (as of October 2010).

Image adjustment functions are activated for the angle of view in the aspect ratio of 4:3 even while "16:9" is being selected for "Aspect ratio". Area masking under the backlight compensation (BLC) function can be set only when the aspect ratio is

"4:3".

If the aspect ratio is changed to "16:9" after setting of the backlight compensation function, the setting of area masking is maintained.

Configure the settings relating to JPEG images [JPEG/H.264]

Click the [JPEG/H.24] tab on the "Image" page. (Pages 13 and 14: How to display/operate the setup menu)

JPEG

Configure the settings such as "Refresh interval (JPEG)*", "Image capture size" and "Image quality" on this section. Refer to page 20 for further information about the settings relating to H.264 images.

[Refresh interval (JPEG)*]

Select an interval to refresh the displayed JPEG image from the following.

0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps/ 2fps/ 3fps/ 5fps/ 6fps*/ 10fps*/ 12fps* (PAL model)/ 15fps*/ 30fps* Default: 5fps

Note:

When "On" is selected for "H.264 transmission", the refresh interval may be longer than the set value when any value with an asterisk (*) on the right is selected.

[Image capture size (Initial display)]

Select the image capture size to display the JPEG image on the "Live" page for the first time.

When "4:3" is selected for "Aspect ratio"

QVGA/ VGA/ 1280 x 960*1

When "16:9" is selected for "Aspect ratio"

320×180/ 640×360/ 1280 ×720*1

Default: 1280x960*1

VGA*2

*1 SP105

*2 SP102

19

Image 19
Contents Operating Instructions Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102EContents Abbreviations PrefaceAbout notations Trademarks and registered trademarksViewer software Monitor images from a single camera Example of IPv4 accessExample of IPv6 access Monitor images on a PCRefresh interval of Jpeg images About the Live + brighter button Image will be brighter Camera title Alarm occurrence indication button*2Zoom buttons Brightness buttons*2Monitor images from multiple cameras Notify of alarm occurrences by e-mail Action at an alarm occurrenceAlarm type Action at an alarm occurrenceTransmit images onto an FTP server Equipped security functions About the network securityHow to display the setup menu Display the setup menu from a PCHow to operate the setup menu About the setup menu window 2Help button 1Maintenance button4Setup 0Schedule buttonConfigure the basic settings Basic Access indicator Green Default On Link/Access indicatorDefault On Power indicator green Link indicator orangeRefresh interval Jpeg Configure the settings relating to Jpeg images JPEG/H.264Default 1280x960*1 Aspect ratio264 1 · H.264 Configure the settings relating to H.264 images JPEG/H.264Transmission priority Default 30fpsDefault Normal Image capture sizeTransmission type Default Multicast TTL/HOPLimit*2Available value 1 Default Refresh intervalExtra zoom SP105 Image adjustPrivacy zone Adaptive black stretch Default Off Mask areaBack light compensationBLC Default Off White balance Light control modeDefault OnHigh Auto slow shutter Simple black & white modeDefault Pedestal level Default ATW1Default Blue gain Default High Chroma gain levelSet mask areas − button Reset buttonExtra zoom + buttonArea Default Off Setup buttonDisplay type Example of entry IP addressAvailable number of characters 1 128 characters Configure the settings relating to the alarm action Alarm Configure the alarm settings AlarmAlarm Alarm image Configure the settings relating to the alarm image AlarmConfigure the VMD settings VMD area Light detection control VMD information additionInformation addition Set the VMD areas VMD area Destination of notification Mail notificationDestination port Panasonic alarm protocol notificationPanasonic alarm protocol Available range 1 Default Retry timesAvailable number of characters 4 32 characters Password Retype passwordAccess level User authHost check Default Off IP addressHost auth Destination IP address Default 1280×960*1 VGA*2Priority stream ActivationConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Default 1h Configure the settings relating to the NTP server NTPTime adjustment Default Time adjustment intervalConfigure the network settings Network Configure the network settings NetworkIPv4 network Common IPv6 networkDefault 20min Easy IP Setup accommodate periodAvailable number of characters 1 64 characters Configure the settings relating to Ddns DdnsDefault Off Host name Access intervalConfigure the settings relating to Snmp Snmp FTP periodic image transmission Default Off Directory nameDefault 1s FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Time & date Maintenance of the camera MaintenanceError description Check the system log System logUpgrade the firmware Upgrade Reset to the default and load the default Html files Reset the settings/Reboot the camera Default resetReboot Displaying the Help screen Viewing HelpCategory Indication Description About the displayed system logError indications relating to login Error indications relating to DdnsCannot access from the web TroubleshootingBrowser No image is displayed No image is displayed or too Alarm occurrence indicationNo indicator lights Image is not being refreshedWhen displaying H.264 images Pop-up or additional options Following message is disPlayed on the information bar Pop-up blocked. To see thisPanasonic Canada Inc