Panasonic WV-SP105E, WV-SP102E operating instructions Upgrade the firmware Upgrade

Page 54

Upgrade the firmware [Upgrade]

Click the [Upgrade] tab of the "Maintenance" page. (Pages 13 and 14: How to display/operate the setup menu) The current firmware can be checked and upgraded to the latest version on this page. Contact the dealer for further information about the firmware upgrade.

[Model no.], [MAC address], [Serial no.], [Firmware version], [IPL version], [HTML version], [IP address (IPv6)], [Viewer software installation counter]

Information of each item will be displayed.

Step 1

Contact the dealer and download the latest firmware onto a PC.

Important:

A blank (space) cannot be used for the name of the directory where the downloaded firmware to be saved.

Step 2

Click the [Browse...] button and designate the down- loaded firmware.

Step 3

Click the radio button respective to the desired option to determine whether or not to initialize the settings after completing the firmware upgrade.

Note:

Note that the settings cannot be restored after an initialization is operated.

Step 4

Click the [Execute] button.

The confirmation window will be displayed. When "Do not reset the settings to the default after the upgrade." is selected, the confirmation window will not be displayed.

Important:

After completing the upgrade, delete temporary internet files. (Page 61)

Upgrade the firmware using a PC in the same sub- net as the unit.

Follow the instructions from the dealer when upgrading the firmware.

Use the designated file (extension: img) for the firm- ware upgrade.

Use the designated file, sp105_xxxx.img, for the firmware upgrade.

*("xxxxx" indicates the version of the firmware.)

Do not turn off the power of the camera during the upgrade process.

Do not perform any operation during upgrading and wait until it completes.

The following network settings will not be reset when upgrading the firmware after selecting "Reset the settings to the default after completing the upgrade. (Except the network settings)".

On/Off for DHCP, IP address, subnet mask, default gateway, HTTP port, line speed, bandwidth control

(bit rate), time & date

The viewer software used on each PC should be licensed individually. Refer to your dealer for the software licensing.

54

Image 54
Contents Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102E Operating InstructionsContents Trademarks and registered trademarks PrefaceAbout notations AbbreviationsViewer software Monitor images on a PC Example of IPv4 accessExample of IPv6 access Monitor images from a single cameraRefresh interval of Jpeg images About the Live Brightness buttons*2 Alarm occurrence indication button*2Zoom buttons + brighter button Image will be brighter Camera titleMonitor images from multiple cameras Action at an alarm occurrence Action at an alarm occurrenceAlarm type Notify of alarm occurrences by e-mailTransmit images onto an FTP server About the network security Equipped security functionsDisplay the setup menu from a PC How to display the setup menuHow to operate the setup menu About the setup menu window 0Schedule button 1Maintenance button4Setup 2Help buttonConfigure the basic settings Basic Link indicator orange Default On Link/Access indicatorDefault On Power indicator green Access indicator GreenAspect ratio Configure the settings relating to Jpeg images JPEG/H.264Default 1280x960*1 Refresh interval JpegConfigure the settings relating to H.264 images JPEG/H.264 264 1 · H.264Image capture size Default 30fpsDefault Normal Transmission priorityRefresh interval Default Multicast TTL/HOPLimit*2Available value 1 Default Transmission typeImage adjust Extra zoom SP105Privacy zone Default Off Mask area Adaptive black stretchBack light compensationBLC Simple black & white mode Light control modeDefault OnHigh Auto slow shutter Default Off White balanceDefault High Chroma gain level Default ATW1Default Blue gain Default Pedestal levelSet mask areas + button Reset buttonExtra zoom − buttonDefault Off Setup button AreaDisplay type IP address Example of entryAvailable number of characters 1 128 characters Configure the alarm settings Alarm Configure the settings relating to the alarm action AlarmAlarm Configure the settings relating to the alarm image Alarm Alarm imageConfigure the VMD settings VMD area VMD information addition Light detection controlInformation addition Set the VMD areas VMD area Mail notification Destination of notificationAvailable range 1 Default Retry times Panasonic alarm protocol notificationPanasonic alarm protocol Destination portUser auth Password Retype passwordAccess level Available number of characters 4 32 charactersDefault Off IP address Host checkHost auth Activation Default 1280×960*1 VGA*2Priority stream Destination IP addressConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Default Time adjustment interval Configure the settings relating to the NTP server NTPTime adjustment Default 1hConfigure the network settings Network Configure the network settings NetworkIPv4 network IPv6 network CommonEasy IP Setup accommodate period Default 20minAccess interval Configure the settings relating to Ddns DdnsDefault Off Host name Available number of characters 1 64 charactersConfigure the settings relating to Snmp Snmp FTP periodic image transmission Default Off Directory nameDefault 1s FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Check the system log System log Maintenance of the camera MaintenanceError description Time & dateUpgrade the firmware Upgrade Reset the settings/Reboot the camera Default reset Reset to the default and load the default Html filesReboot Viewing Help Displaying the Help screenAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to loginTroubleshooting Cannot access from the webBrowser No image is displayed Image is not being refreshed Alarm occurrence indicationNo indicator lights No image is displayed or tooWhen displaying H.264 images Pop-up blocked. To see this Following message is disPlayed on the information bar Pop-up or additional optionsPanasonic Canada Inc