Panasonic WV-SP102E, WV-SP105E operating instructions Set the VMD areas VMD area, Step

Page 35

Set the VMD areas [VMD area]

Set the areas to activate the VMD function.

Important:

When the settings are being configured on the setup menu, sometimes the VMD function may not work cor- rectly.

Step 1

Set the video motion detection area by dragging the mouse on the screen.

The designated area will become the VMD area "1(White)" and the outline will be displayed. When

2 - 4 VMD areas are set, each area will be numbered in order. The areas will be identified by the respec- tive outline colors. The "Status" of the outline to be set for the area will become "On".

Step 2

Adjust "Detection area" and "Detection sensitivity" using the slider.

"Detection area" can be adjusted by moving the slider between the left end position and the center position. "Detection sensitivity" can be adjusted by moving the slider between the left end position and the right end position.

Refer to page 33 for further information about the "Detection sensitivity" and "Detection area".

Note:

When "Detection area" cannot be adjusted properly by moving the slider, adjust "Detection sensitivity" while checking the motion detection status.

Step 3

Click the [Set] button after completing the settings.

Important:

The setting will not be applied unless the [Set] but- ton is clicked.

Step 4

To invalidate the VMD area, click the [Set] button after selecting "Off" for "Status" of the VMD area to be invali- dated.

The outline of the invalidated VMD area will turn to a dotted line. When the VMD area is invalidated, no alarm will occur even when a motion can be recog- nized in the area.

Step 5

To delete the VMD area, click the [Delete] button corre- sponding to the area to be deleted.

The outline of the respective VMD area will disap- pear.

Step 6

Click the [Setup] button.

The edited settings will be applied.

35

Image 35
Contents Operating Instructions Model No. WV-SP105, WV-SP102 WV-SP105E, WV-SP102EContents Abbreviations PrefaceAbout notations Trademarks and registered trademarksViewer software Monitor images from a single camera Example of IPv4 accessExample of IPv6 access Monitor images on a PCRefresh interval of Jpeg images About the Live + brighter button Image will be brighter Camera title Alarm occurrence indication button*2Zoom buttons Brightness buttons*2Monitor images from multiple cameras Notify of alarm occurrences by e-mail Action at an alarm occurrenceAlarm type Action at an alarm occurrenceTransmit images onto an FTP server Equipped security functions About the network securityHow to display the setup menu Display the setup menu from a PCHow to operate the setup menu About the setup menu window 2Help button 1Maintenance button4Setup 0Schedule buttonConfigure the basic settings Basic Access indicator Green Default On Link/Access indicatorDefault On Power indicator green Link indicator orangeRefresh interval Jpeg Configure the settings relating to Jpeg images JPEG/H.264Default 1280x960*1 Aspect ratio264 1 · H.264 Configure the settings relating to H.264 images JPEG/H.264Transmission priority Default 30fpsDefault Normal Image capture sizeTransmission type Default Multicast TTL/HOPLimit*2Available value 1 Default Refresh intervalPrivacy zone Image adjustExtra zoom SP105 Back light compensationBLC Default Off Mask areaAdaptive black stretch Default Off White balance Light control modeDefault OnHigh Auto slow shutter Simple black & white modeDefault Pedestal level Default ATW1Default Blue gain Default High Chroma gain levelSet mask areas − button Reset buttonExtra zoom + buttonDisplay type Default Off Setup buttonArea Available number of characters 1 128 characters IP addressExample of entry Alarm Configure the alarm settings AlarmConfigure the settings relating to the alarm action Alarm Alarm image Configure the settings relating to the alarm image AlarmConfigure the VMD settings VMD area Information addition VMD information additionLight detection control Set the VMD areas VMD area Destination of notification Mail notificationDestination port Panasonic alarm protocol notificationPanasonic alarm protocol Available range 1 Default Retry timesAvailable number of characters 4 32 characters Password Retype passwordAccess level User authHost auth Default Off IP addressHost check Destination IP address Default 1280×960*1 VGA*2Priority stream ActivationConfigure the settings relating to the mail server Mail Configure the settings relating to the FTP server FTP Default 1h Configure the settings relating to the NTP server NTPTime adjustment Default Time adjustment intervalIPv4 network Configure the network settings NetworkConfigure the network settings Network Common IPv6 networkDefault 20min Easy IP Setup accommodate periodAvailable number of characters 1 64 characters Configure the settings relating to Ddns DdnsDefault Off Host name Access intervalConfigure the settings relating to Snmp Snmp FTP periodic image transmission Default Off Directory nameDefault 1s FTP periodic image transmissionHow to set the schedules How to delete the set schedule Configure the settings relating to the schedules Schedule Time & date Maintenance of the camera MaintenanceError description Check the system log System logUpgrade the firmware Upgrade Reboot Reset the settings/Reboot the camera Default resetReset to the default and load the default Html files Displaying the Help screen Viewing HelpCategory Indication Description About the displayed system logError indications relating to login Error indications relating to DdnsBrowser TroubleshootingCannot access from the web No image is displayed No image is displayed or too Alarm occurrence indicationNo indicator lights Image is not being refreshedWhen displaying H.264 images Pop-up or additional options Following message is disPlayed on the information bar Pop-up blocked. To see thisPanasonic Canada Inc