Xantrex Technology 809-0915 manual Relay Function, Type 5 Connection Diagram

Page 29

Xanbus Automatic Generator Start Installation

Type 5

Type 5 is a three-wire StartStop configuration that uses relay 3 to provide a 15-second preheat signal.

Relay Function	Preset Configuration Setting

Crank time	15 s

Crank retry time	15 s

AGS Harness W ires

Generator W ires

Relay 1

Relay 2

Relay 3

12

13

14

16

17

18

19

20

				GENERATOR RUN SIGNAL
				GENERATOR RUN SIGNAL
				GENERATOR RUN SIGNAL RETURN
			5A fuse	GENERATOR RUN SIGNAL RETURN
				STOP/PREHEAT



			5A fuse	START

5A fuse FUEL PRIME (PREHEAT)

12V GENERATOR BATTERY+

Gen Cool Down	30 s

Gen Spin Down	3 s

Shutdown bypass time	0 s

Start tries	3

For additional information, see “Circuit Limitations” on page 11.

Figure 11 Type 5 Connection Diagram

Relay Function	Preset Configuration Setting

Relay 1 mode	StartStop
Relay 3 mode	Preheat

Gen Run signal hold time	2 s

Preheat time	15 s

Preheat to crank delay	2 s

975-0082-01-01

19

Image 29

Contents Xanbus Automatic Generator Start AGS Page Exclusion for Documentation TrademarksDate and Revision Document Part NumberPurpose About This GuideScope AudienceRelated Information Reference Important Safety InstructionsRestrictions on USE FCC Information to the UserPage Contents Page Xanbus Automatic Generator Start AGS Basic Function IntroductionSystem Requirements Functions AGS unit Material ListXanbus-Enabled Products and Accessories Front panel features FeaturesXanbus Bottom panel featuresChoosing a Location Xanbus Automatic Generator Start InstallationMaterials and Tools Required Shock and Energy Hazards Routing ConnectionsMounting the Unit Installation OverviewCircuit Parameter Circuit Maximum Wiring to the 20-contact ConnectorFt m Over 30 ft m To install the AGS using the wiring harnessXanbus Automatic Generator Start Installation Connecting the Generator Type Relay Function Preset Configuration SettingType 2 Connection Diagram Type 3 Connection Diagram Type 4 Connection Diagram Relay Function Type 5 Connection DiagramType 6 Connection Diagram Type 7 Connection Diagram two-wire Type 8 Connection Diagram two-wire Type 9 Connection Diagram Type 10 Connection Diagram Type 11 Connection Diagram Type 12 Connection Diagram Type 13 Connection Diagram Type 14 Connection Diagram two-wire Number Function Wire Color Connecting the Thermostats optionalWire Connecting an External Shutdown optional Connecting an External Manual ON/OFF Switch optionalWire Wiring Harness Number Function Wire Color Connecting an External ON/OFF LEDExternal ON/OFF Switch and LED Wiring Diagram To connect the wiring harness to the AGS Connecting the Wiring Harness to the AGSConnecting the AGS to the Xanbus Network Connecting the Xanbus System Control Panel SCP Verifying Power Is AvailableOverview Configuration of the Xanbus AGSTo change operational settings on the AGS Menu Accessing the AGS MenuXanbus Automatic Generator Start AGS Menu Xanbus AGS Menu To configureAGS Configuration Menu Contents Value Description Configuration MenuQT En QT Begin Gen Type QT EndDescription Cfg Trigger Start DCV 30 sec Values DefaultStart DCV 15 min Start DCV 24 hr Start DCV 2 hrStop Absorb Stop FloatStop Temp2 Temp1Start Load Value DefaultLoad Stop Load Starter Cool Down Cfg GenGen Spin Down Gen Cool DownExercise Per Max Run TimeExercise Time Exercise DurGen Run Hold Time Relay3Crank Time Crank DelayCrank Retry Time Preheat TimeGen Start Tries GenMode Restore DefaultsAutomatic Mode Manual Off Mode Manual On ModeMode View Fault LogView Device Info View Event LogItems User SettingsOperation of the Xanbus AGS Accessing the AGS Home ScreenTo start the generator manually Starting and Stopping the GeneratorTo enable Quiet Time Using Quiet TimeModes of Operation Putting the AGS in Standby ModeTo return the AGS to Operating Mode Returning the AGS to Operating ModeTo view a message from a fault list or warning list TroubleshootingTroubleshooting AGS Warning Messages AGS Fault Messages Fault Reference TableElectrical Specifications SpecificationsEnvironmental Specifications Regulatory ApprovalsDimensions Weight Mounting Connectors Physical SpecificationsWarranty Warranty and Return InformationDisclaimer Warranty and Return InformationReturn Procedure Return Material Authorization PolicyInformation About Your System Generator Starting Types Recommended FeaturesAppendix a Generator Auto Start Requirements and Types Three-Wire Onan Two WireThree-Wire Automotive RunMode Appendix B Relay TimingMomentaryRun Mode Timing Diagram MomentaryRun ModeGlowStop Mode Timing Diagram GlowStop ModeStartStop Mode Timing Diagram StartStop ModePulseStop Mode Timing Diagram PulseStop ModePulseStop Mode Relay 1 Behavior Page Page Xantrex Technology USA Inc