Xantrex Technology 809-0915 manual AGS Configuration Menu Contents

Page 49

Configuration of the Xanbus AGS

When the AGS Home Screen is first displayed, the menu defaults to the

GenMode Menu. If configuration changes need to be made, the

Configuration Menu can be accessed by pressing the Enter, Up arrow, and

Down arrow buttons all at same time to access the Advanced Settings.

AC In/Charge	XAGS 00: Setup		STBY/ON
Inverter On	XAGS 00: Setup		STBY/ON
Inverter On	GenMode	[ManualOff]	Fault Clear
Low Battery	Mode	[Operating]	Xanbus AGS Menu
Fault	Clear Faults Warnings		Xanbus AGS Menu
Fault	View Device Info
			XAGS 00: Setup
			Advanced Settings
			GenMode	[ManualOff]
	Enter	Func	Clear Faults Warnings
			View Device Info
Xanbus System Control Panel (SCP)			FGA: 809-0921
			XAGS 00: Setup
		To access the Advanced Settings menu,
		Press Enter and Up and Down arrows together Advanced Settings
			GenMode	[ManualOff]

Clear Faults Warnings

View Device Info

XAGS 00: Config

QT EN		[Enabled]
QT Begin		[9:00PM]
QT End		[8:00AM]
Gen Type		[2]
Cfg Trigger
Cfg Trigger
Cfg Gen

Multi-Unit Config

Restore Defaults

To change configuration parameters...

Press Enter to move forward into the Config menu.

XAGS 00: Triggers

Start DCV 30 Sec	[40.0V]
Start DCV 15 Sec	[Disabled]
Start DCV 2 hr	[Disabled]
Start DCV 24 Hr	[Disabled]
Stop Float	[Disabled]
Stop Absorb	[Disabled]
StopV	[Disabled]
Temp1	[Disabled]
Temp2	[Disabled]
Load	[Disabled]
Start Load	[15A]
Stop Load	[10A]
XAGS 00: Gen
Starter Cool Down	[60sec]
Gen Cool Down	[30sec]
Gen Spin Down	[3sec]
Max Runtime	[4hours]
Exercise per	[21days]
Exercise Dur	[30min]
Exercise Time	[9:00AM]
Relay 3	[Not Used]
Gen Run Hold Time	[0.5s]
Crank Delay	[1sec]
Crank Time	[30sec]

Use these buttons to change the settings.

Press ENTER to accept the new setting.

To return to the B asic Settings menu,

Press Enter and Up and Down arrows together

Use these buttons to select the desired menu.

Press ENTER to move the cursor to the changeable settings.

Press Func to return to the Xanbus AGS Home screen.

Crank Retry Time		[40sec]
Preheat Time		[0sec]
Gen Start Tries		[3]

XAGS 00: Gen
Dev Name		[AGS]
Dev Number		[00]
Connections

XAGS 00: Conn

DC Conn	[HouseBatt1]
AC In	[Grid1]
AC Out	[ACLoad]
Generator	[Gen1]

Figure 32 AGS Configuration Menu Contents

975-0082-01-01

39

Image 49

Contents Xanbus Automatic Generator Start AGS Page Exclusion for Documentation TrademarksDate and Revision Document Part NumberPurpose About This GuideScope AudienceRelated Information Reference Important Safety InstructionsRestrictions on USE FCC Information to the UserPage Contents Page Xanbus Automatic Generator Start AGS Basic Function IntroductionSystem Requirements Functions AGS unit Material ListXanbus-Enabled Products and Accessories Front panel features FeaturesXanbus Bottom panel featuresMaterials and Tools Required Xanbus Automatic Generator Start InstallationChoosing a Location Shock and Energy Hazards Routing ConnectionsMounting the Unit Installation OverviewCircuit Parameter Circuit Maximum Wiring to the 20-contact ConnectorFt m Over 30 ft m To install the AGS using the wiring harnessXanbus Automatic Generator Start Installation Connecting the Generator Type Relay Function Preset Configuration SettingType 2 Connection Diagram Type 3 Connection Diagram Type 4 Connection Diagram Relay Function Type 5 Connection DiagramType 6 Connection Diagram Type 7 Connection Diagram two-wire Type 8 Connection Diagram two-wire Type 9 Connection Diagram Type 10 Connection Diagram Type 11 Connection Diagram Type 12 Connection Diagram Type 13 Connection Diagram Type 14 Connection Diagram two-wire Wire Connecting the Thermostats optionalNumber Function Wire Color Connecting an External Shutdown optional Connecting an External Manual ON/OFF Switch optionalWire Wiring Harness Number Function Wire Color Connecting an External ON/OFF LEDExternal ON/OFF Switch and LED Wiring Diagram To connect the wiring harness to the AGS Connecting the Wiring Harness to the AGSConnecting the AGS to the Xanbus Network Connecting the Xanbus System Control Panel SCP Verifying Power Is AvailableOverview Configuration of the Xanbus AGSTo change operational settings on the AGS Menu Accessing the AGS MenuXanbus Automatic Generator Start AGS Menu Xanbus AGS Menu To configureAGS Configuration Menu Contents QT En Configuration MenuValue Description QT Begin Gen Type QT EndDescription Cfg Trigger Start DCV 30 sec Values DefaultStart DCV 15 min Start DCV 24 hr Start DCV 2 hrStop Absorb Stop FloatStop Temp2 Temp1Load Value DefaultStart Load Stop Load Starter Cool Down Cfg GenGen Spin Down Gen Cool DownExercise Per Max Run TimeExercise Time Exercise DurGen Run Hold Time Relay3Crank Time Crank DelayCrank Retry Time Preheat TimeGen Start Tries Automatic Mode Restore DefaultsGenMode Manual Off Mode Manual On ModeMode View Fault LogView Device Info View Event LogItems User SettingsOperation of the Xanbus AGS Accessing the AGS Home ScreenTo start the generator manually Starting and Stopping the GeneratorTo enable Quiet Time Using Quiet TimeModes of Operation Putting the AGS in Standby ModeTo return the AGS to Operating Mode Returning the AGS to Operating ModeTo view a message from a fault list or warning list TroubleshootingTroubleshooting AGS Warning Messages AGS Fault Messages Fault Reference TableElectrical Specifications SpecificationsEnvironmental Specifications Regulatory ApprovalsDimensions Weight Mounting Connectors Physical SpecificationsWarranty Warranty and Return InformationDisclaimer Warranty and Return InformationReturn Procedure Return Material Authorization PolicyInformation About Your System Appendix a Generator Auto Start Requirements and Types Recommended FeaturesGenerator Starting Types Three-Wire Onan Two WireThree-Wire Automotive RunMode Appendix B Relay TimingMomentaryRun Mode Timing Diagram MomentaryRun ModeGlowStop Mode Timing Diagram GlowStop ModeStartStop Mode Timing Diagram StartStop ModePulseStop Mode Timing Diagram PulseStop ModePulseStop Mode Relay 1 Behavior Page Page Xantrex Technology USA Inc