Xantrex Technology 809-0915 manual Xanbus Automatic Generator Start AGS Menu

Page 48

Configuration of the Xanbus AGS

The Xanbus Automatic Generator Start (AGS) Menu

The Xanbus Automatic Generator Start (AGS) menu provides the ability to configure the changeable parameters, select the generator’s operating mode, clear fault warnings and view device information.

					Xanbus AGS Menu		To configure...
	AC In/Charge	XAGS 00: Setup		STBY/ON	XAGS 00: Setup		XAGS 00: Setup
	Inverter On
		GenMode	[ManualOff]	Fault Clear	GenMode	[ManualOff]	Advanced Settings

	Low Battery	Mode	[Operating]		Mode	[Operating]	GenMode	[ManualOff]
		Clear Faults Warnings			Clear Faults Warnings		Clear Faults Warnings
	Fault	View Device Info			View Device Info		View Device Info

The Xanbus Automatic Generator Start (AGS) Menu Home Screen is divided into five sections.

•Advanced Settings (Configuration Settings)

•GenMode (Manual on/Manual off/Automatic)

•Mode of Operation (Operating/Standby)

•Clear Fault Warnings

•View Device Info

EnterFunc

Xanbus System Control Panel (SCP)

FGA: 809-0921

To select the Generator

Starting Mode...

To select the Device

Operating Mode...

To clear faults and

warnings...

To view device

information...

Use these buttons to	Press the ENTER button to
move UP or DOWN.	select the menu item.
XAGS 00: Setup		XAGS 00: Setup
GenMode	[ManualOff]	GenMode	[ManualOff]
Mode	[Operating]	Mode	[Operating]
Clear Faults Warnings		Clear Faults Warnings
View Device Info		View Device Info
XAGS 00: Setup		XAGS 00: Setup
GenMode	[ManualOff]	GenMode	[ManualOff]
Mode	[Operating]	Mode	[Operating]
Clear Faults Warnings		Clear Faults Warnings
View Device Info		View Device Info
		Use these buttons to	Press the ENTER button
		change the settings.	accepts the new setting.
XAGS 00: Setup
GenMode	[ManualOff]
Mode	[Operating]

Clear Faults Warnings		Press the Func button to
View Device Info		Press the Func button to
		return to the AGS Home.
XAGS 00: Setup
GenMode	[ManualOff]
Mode	[Operating]	Press the Func button to

Clear Faults Warnings

View Device Info

return to the FSW System Home Screen.

Figure 31 AGS Basic Menu Contents

38	Xanbus Automatic Generator Start (AGS) Owner’s Guide

Image 48

Contents Xanbus Automatic Generator Start AGS Page Trademarks Exclusion for DocumentationDate and Revision Document Part NumberAbout This Guide PurposeScope AudienceRelated Information Important Safety Instructions ReferenceFCC Information to the User Restrictions on USEPage Contents Page Introduction Xanbus Automatic Generator Start AGS Basic FunctionSystem Requirements Functions Material List AGS unitXanbus-Enabled Products and Accessories Features Front panel featuresBottom panel features XanbusXanbus Automatic Generator Start Installation Materials and Tools RequiredChoosing a Location Routing Connections Shock and Energy HazardsInstallation Overview Mounting the UnitWiring to the 20-contact Connector Circuit Parameter Circuit MaximumTo install the AGS using the wiring harness Ft m Over 30 ft mXanbus Automatic Generator Start Installation Connecting the Generator Relay Function Preset Configuration Setting TypeType 2 Connection Diagram Type 3 Connection Diagram Type 4 Connection Diagram Type 5 Connection Diagram Relay FunctionType 6 Connection Diagram Type 7 Connection Diagram two-wire Type 8 Connection Diagram two-wire Type 9 Connection Diagram Type 10 Connection Diagram Type 11 Connection Diagram Type 12 Connection Diagram Type 13 Connection Diagram Type 14 Connection Diagram two-wire Connecting the Thermostats optional WireNumber Function Wire Color Connecting an External Manual ON/OFF Switch optional Connecting an External Shutdown optionalConnecting an External ON/OFF LED Wire Wiring Harness Number Function Wire ColorExternal ON/OFF Switch and LED Wiring Diagram Connecting the Wiring Harness to the AGS To connect the wiring harness to the AGSConnecting the AGS to the Xanbus Network Verifying Power Is Available Connecting the Xanbus System Control Panel SCPConfiguration of the Xanbus AGS OverviewAccessing the AGS Menu To change operational settings on the AGS MenuXanbus AGS Menu To configure Xanbus Automatic Generator Start AGS MenuAGS Configuration Menu Contents Configuration Menu QT EnValue Description QT Begin QT End Gen TypeDescription Cfg Trigger Values Default Start DCV 30 secStart DCV 15 min Start DCV 2 hr Start DCV 24 hrStop Float Stop AbsorbStop Temp1 Temp2Value Default LoadStart Load Stop Load Cfg Gen Starter Cool DownGen Cool Down Gen Spin DownMax Run Time Exercise PerExercise Dur Exercise TimeRelay3 Gen Run Hold TimeCrank Delay Crank TimeCrank Retry Time Preheat TimeGen Start Tries Restore Defaults Automatic ModeGenMode Manual On Mode Manual Off ModeView Fault Log ModeView Device Info View Event LogUser Settings ItemsAccessing the AGS Home Screen Operation of the Xanbus AGSStarting and Stopping the Generator To start the generator manuallyUsing Quiet Time To enable Quiet TimePutting the AGS in Standby Mode Modes of OperationReturning the AGS to Operating Mode To return the AGS to Operating ModeTroubleshooting To view a message from a fault list or warning listTroubleshooting AGS Warning Messages Fault Reference Table AGS Fault MessagesSpecifications Electrical SpecificationsEnvironmental Specifications Regulatory ApprovalsPhysical Specifications Dimensions Weight Mounting ConnectorsWarranty and Return Information WarrantyWarranty and Return Information DisclaimerReturn Material Authorization Policy Return ProcedureInformation About Your System Recommended Features Appendix a Generator Auto Start Requirements and TypesGenerator Starting Types Two Wire Three-Wire OnanThree-Wire Automotive Appendix B Relay Timing RunModeMomentaryRun Mode MomentaryRun Mode Timing DiagramGlowStop Mode GlowStop Mode Timing DiagramStartStop Mode StartStop Mode Timing DiagramPulseStop Mode PulseStop Mode Timing DiagramPulseStop Mode Relay 1 Behavior Page Page Xantrex Technology USA Inc