Xantrex Technology 809-0915 manual Troubleshooting

Page 80

Troubleshooting

Warning Reference Table

Table 6	AGS Warning Messages

Warning	Message	Self-clearing?	Cause	Action
Number

W200	Generator	No	Generator was stopped	Acknowledge the
	was stopped		by an external Manual	warning. To resume
	manually.		Off switch.	automatic starts and
				stops, change the AGS
				mode to [Automatic].

W201	Generator	No	Generator was started	Acknowledge the
	was started		by an external Manual	warning. To resume
	manually.		On switch	automatic starts and
				stops, change the AGS
				mode to [Automatic].

W202	Unable to	Yes	The AGS tried, but	No action required. The
	start		could not start the	AGS will try to start the
	generator.		generator.	generator again until it
	AGS will try			reaches the maximum
	again.			number of start tries.

W203	Manual Off:	No	The generator has run	Acknowledge the
	Max		for its maximum	warning. Return the
	generator run		allowable time. The	AGS to the desired
	time reached.		AGS has stopped the	GenMode [Automatic
	Reset		generator and changed	or ManualOn]. Ensure
	GenMode.		the GenMode to	generator has fuel and
			[ManualOff].	is supplying the
				required power for
				battery charging and
				loads.

Table 6	AGS Warning Messages (Continued)

Warning	Message	Self-clearing?	Cause	Action
Number

W205	Generator	Yes	The generator was	Check your generator.
	started by its		started, but not by the	Stop it using the switch
	switch. Use		AGS.	or control panel on the
	its switch to			generator.
	stop.

W206	Mismatched	No	You have set a start	Acknowledge warning
	triggers.		trigger, but not a	and set a stop trigger.
	Enable stop		corresponding stop
	trigger or		trigger.
	disable start
	trigger.

W207	Mismatched	No	You have set a stop	Acknowledge warning
	triggers.		trigger, but not a	and set a start trigger.
	Enable start		corresponding start
	trigger or		trigger.
	disable stop
	trigger.

W208	Automatic	No	You are attempting to	Acknowledge warning
	start and stop		enter Automatic Mode	and set start and stop
	triggers not		without setting triggers.	triggers.
	enabled.
	Configure
	triggers.

70	Xanbus Automatic Generator Start (AGS) Owner’s Guide

Image 80

Contents Xanbus Automatic Generator Start AGS Page Trademarks Exclusion for DocumentationDate and Revision Document Part NumberAbout This Guide PurposeScope AudienceRelated Information Important Safety Instructions ReferenceFCC Information to the User Restrictions on USEPage Contents Page Introduction Xanbus Automatic Generator Start AGS Basic FunctionSystem Requirements Functions Material List AGS unitXanbus-Enabled Products and Accessories Features Front panel featuresBottom panel features XanbusChoosing a Location Xanbus Automatic Generator Start InstallationMaterials and Tools Required Routing Connections Shock and Energy HazardsInstallation Overview Mounting the UnitWiring to the 20-contact Connector Circuit Parameter Circuit MaximumTo install the AGS using the wiring harness Ft m Over 30 ft mXanbus Automatic Generator Start Installation Connecting the Generator Relay Function Preset Configuration Setting TypeType 2 Connection Diagram Type 3 Connection Diagram Type 4 Connection Diagram Type 5 Connection Diagram Relay FunctionType 6 Connection Diagram Type 7 Connection Diagram two-wire Type 8 Connection Diagram two-wire Type 9 Connection Diagram Type 10 Connection Diagram Type 11 Connection Diagram Type 12 Connection Diagram Type 13 Connection Diagram Type 14 Connection Diagram two-wire Number Function Wire Color Connecting the Thermostats optionalWire Connecting an External Manual ON/OFF Switch optional Connecting an External Shutdown optionalConnecting an External ON/OFF LED Wire Wiring Harness Number Function Wire ColorExternal ON/OFF Switch and LED Wiring Diagram Connecting the Wiring Harness to the AGS To connect the wiring harness to the AGSConnecting the AGS to the Xanbus Network Verifying Power Is Available Connecting the Xanbus System Control Panel SCPConfiguration of the Xanbus AGS OverviewAccessing the AGS Menu To change operational settings on the AGS MenuXanbus AGS Menu To configure Xanbus Automatic Generator Start AGS MenuAGS Configuration Menu Contents Value Description Configuration MenuQT En QT Begin QT End Gen TypeDescription Cfg Trigger Values Default Start DCV 30 secStart DCV 15 min Start DCV 2 hr Start DCV 24 hrStop Float Stop AbsorbStop Temp1 Temp2Start Load Value DefaultLoad Stop Load Cfg Gen Starter Cool DownGen Cool Down Gen Spin DownMax Run Time Exercise PerExercise Dur Exercise TimeRelay3 Gen Run Hold TimeCrank Delay Crank TimeCrank Retry Time Preheat TimeGen Start Tries GenMode Restore DefaultsAutomatic Mode Manual On Mode Manual Off ModeView Fault Log ModeView Device Info View Event LogUser Settings ItemsAccessing the AGS Home Screen Operation of the Xanbus AGSStarting and Stopping the Generator To start the generator manuallyUsing Quiet Time To enable Quiet TimePutting the AGS in Standby Mode Modes of OperationReturning the AGS to Operating Mode To return the AGS to Operating ModeTroubleshooting To view a message from a fault list or warning listTroubleshooting AGS Warning Messages Fault Reference Table AGS Fault MessagesSpecifications Electrical SpecificationsEnvironmental Specifications Regulatory ApprovalsPhysical Specifications Dimensions Weight Mounting ConnectorsWarranty and Return Information WarrantyWarranty and Return Information DisclaimerReturn Material Authorization Policy Return ProcedureInformation About Your System Generator Starting Types Recommended FeaturesAppendix a Generator Auto Start Requirements and Types Two Wire Three-Wire OnanThree-Wire Automotive Appendix B Relay Timing RunModeMomentaryRun Mode MomentaryRun Mode Timing DiagramGlowStop Mode GlowStop Mode Timing DiagramStartStop Mode StartStop Mode Timing DiagramPulseStop Mode PulseStop Mode Timing DiagramPulseStop Mode Relay 1 Behavior Page Page Xantrex Technology USA Inc