Weber 56069 manual GAS Leak Testing, To Connect the Hose to the Cylinder, Check for GAS Leaks

Page 14

14

CONNECTING GAS SUPPLY

Some LP tanks have differing top collar assembles. (The top collar is the metal protective ring around the valve.) One series of tanks mount with the valve facing front

(a). The other tanks mount with the valve facing away from the fuel scale (b). Weber recommends the use of cylinder manufacturer’s Manchester and Worthington, with a

47.6lb water capacity. Other cylinders may be acceptable for use with the appliance provided they are compatible with the appliance retention means (see illustrations).

The LP cylinder is installed inside the tank enclosure or tank cabinet, on the tank scale.

1)Turn the LP cylinder so the opening of the valve is either to the front, side or rear of the Weber® gas barbecue. Lift and hook the cylinder onto the fuel gauge.

2)Lift tank up into position on the tank scale.

3)Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing nut.

b a

TO CONNECT THE HOSE TO THE CYLINDER:

4)Remove the plastic dust cover from the valve.

5)Screw the regulator coupling onto the tank valve, clockwise, or to the right. Hand- tighten only.

Note: This connection tightens clockwise and will not allow gas to flow unless the connection is tight. The connection requires tightening by hand only.

WARNING: Do not use a wrench to tighten the connection. Using a wrench could damage the regulator coupling and could cause a leak.

6) Check for gas leaks.

GAS LEAK TESTING

CHECK FOR GAS LEAKS

After a period of nonuse, we recommend that you perform the following maintenance procedures for your safety.

WARNING: Check the hose before each use of the grill for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, do not use the grill. Replace using only Summit® authorized replacement hose. Contact the Customer Service Representative in your area using the contact information on our web site.

Log onto www.weber.com®.

Inspect the burner for correct flame pattern. Clean if necessary, following the procedures outlined in the “General Maintenance” section of this manual.

Check all gas fittings for leaks.

All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ANSI Z223.1/NFPA 54.

DANGER

Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, which can cause serious bodily injury or death and damage to property.

WARNING: You should check for gas leaks every time you disconnect and reconnect a gas fitting.

Note - All factory-made connections have been thoroughly checked for gas leaks.The burners have been flame-tested.As a safety precaution however, you should recheck all fittings for leaks before using your Weber® appliances. Shipping and handling may loosen or damage a gas fitting.

WARNING: Perform these leak checks even if your appliance was dealer or store assembled.

You will need: a soap and water solution, and a rag or brush to apply it.

Note - Since some leak test solutions, including soap and water, may be slightly corrosive, all connections should be rinsed with water after checking for leaks. Make sure side burner is OFF.

To perform leak checks: open cylinder valve by turning the cylinder valve hand-wheel counterclockwise.

WARNING: Do not ignite burners when leak checking.

WWW.WEBER.COM®

Image 14
Contents #56069 Wash hands after handling this product Liquid Propane GAS Units onlyGarantía WARRANTY, GARANTÍA, GarantieWarranty GarantieExploded VIEW, Diagrama DE DESPIECE, Vision Eclatee Hardware LIST, Lista DE LOS HERRAJES, Liste DU Materiel Grate Side Burner Box Igniter ModuleIsland Structure Configuration Options InstallationFor Installation in Canada OperatingLocating Your BUILT-IN Side Burner Appliance InstallationBUILT-IN Structure Cutout Dimensions Clearance from Combustible Surfaces or StructuresGeneral Construction Details BUILT-IN GAS Line LocationsMounting the Side Burner Installation GAS Line Piping INSTALLATION/GAS InstructionsTypical Bulk Propane GAS Supply Installation Test Connections Typical 20 LP Propane GAS Supply InstallationGAS Instructions Connecting GAS Supply Connect GAS SupplyImportant LP Cylinder Information Connecting GAS SupplyConnecting the Liquid Propane Cylinder Leak Check PreparationCheck for GAS Leaks GAS Leak TestingTo Connect the Hose to the Cylinder Check Side Burner Component Check GAS Supply ConnectionsCanada GAS InstructionsSafe Handling Tips for Liquid Propane GAS Cylinders Liquid Propane LP CylindersTo Extinguish Operating InstructionsSide Burner Lighting Instructions Operating Instructions Manually Lighting the Side BurnerProblem Check Cure Side Burner TroubleshootingGeneral Maintenance Side Burner MaintenanceBurner Flame Pattern General MaintenanceCleaning #42376 Herrajes PGAdvertencias Peligros Y AdvertenciasPeligro Únicamente Unidades DE GAS Propano LicuadoOperación Opciones DE Configuración DE LAS Estructuras Tipo IslaInstalación Para LA Instalación EN CanadáUbicación DEL Quemador Lateral Empotrado Dimensiones seccionales ToleranciasInstalación Separación DE LAS Superficies O Estructuras CombustiblesDetalles Generales DE Construcción Ubicaciones DE LAS Líneas DE GAS EmpotradasMontaje DEL Quemador Lateral Instalación Tubería DE LA Línea DE GAS INSTALACIÓN/INSTRUCCIONES Para EL GASInstalación Típica DE Suministro DE GAS Propano a Granel Especificaciones Generales Para LA TuberíaInstrucciones Para EL GAS Pruebe LAS ConexionesConexión DEL Suministro DE GAS Conectar EL Suministro DE GASConexión DEL Cilindro DE Propano Licuado Conexión DEL Suministro DE GASPreparativos Para LA Búsqueda DE Fugas Llene EL Cilindro DE Propano LicuadoCompruebe QUE no Haya Fugas DE GAS Pruebas Para Detectar Fugas DE GASPara Conectar LA Manguera AL Cilindro Revise LAS Conexiones DE Suministro DE GAS Pruebas Para Detectar Fugas DE GASRevise EL Quemador Lateral Requisitos DE LOS Cilindros DE Propano Licuado Instrucciones Para EL GASCilindros DE Propano Licuado EN Canadá Requisitos DE LOS Cilindros DE Propano LicuadoAdvertencia Instrucciones DE OperaciónInstrucciones Para Encender EL Quemador Lateral Para ApagarInstrucciones DE Operación Encendido Manual DEL Quemador Lateral PeligroMantenimiento General Resolución DE Problemas CON EL Quemador LateralProblema Revisar Remedio EncendedorPatrón DE LA Llama DEL Quemador Limpieza42376 Materiel PGMises EN Garde Appareils a GAZ Propane UniquementUtilisation Pour L’INSTALLATION AU CanadaOptions DE Configuration Pour LA Structure EN Ilot Localisation DE Votre Bruleur Lateral Integre Dimensions Pour LE Decoupage DE LA Structure IntegreeDimensions pour le découpage Tolérances Brûleur latéralGeneralites SUR LA Construction Emplacements DE LA Conduite DE GAZ IntegreeMontage DU Bruleur Lateral Installation Canalisations DE GAZ Instructions Pour L’INSTALLATION/GAZInstallation D’ARRIVEE DE GAZ Propane EN Vrac Typique Generalites Relatives AUX CanalisationsTest DES Raccords Installation DE L’ALIMENTATION EN GAZ PropaneInstructions Relatives AU GAZ Raccordement DE L’ARRIVEE DE GAZ Raccordement DE L’ARRIVEE DE GAZPreparation DE LA Detection DES Fuites Raccordement DE L’ARRIVEE DE GAZInformations Importantes Relatives a LA Bouteille DE PL Connexion DE LA Bouteille DE Propane LiquideDetection DES Fuites DE GAZ Detection DES Fuites DE GAZPour Connecter LE Tuyau À LA Bouteille Verifiez LES Composants DU Bruleur Lateral Verifiez LES Raccords DE L’ARRIVEE DE GAZExigences Relatives À LA Bouteille DE Propane Liquide Instructions Relatives AUX GAZBouteilles DE GAZ Propane Liquide PL AU CanadaMise EN Garde Mode D’EMPLOIInstructions Pour L’ALLUMAGE DU Bruleur Lateral Pour EteindreMode D’EMPLOI Allumage Manuel DU Bruleur LateralMaintenance DU Bruleur Lateral Maintenance GeneraleProbleme Verification Solution Depannage DU Bruleur LateralNettoyage Maintenance GeneraleAspect DE LA Flamme DU Bruleur Page WEBER-STEPHEN Products CO