Friedrich MW24Y3F Name of Parts, Indoor Unit Operating Control Panel Fig Manual Auto button

Page 4

NAME OF PARTS

Fig. 1 Indoor Unit

1Operating Control Panel (Fig. 2)

2MANUAL AUTO button

When kept on pressing the MANUAL AUTO button for more than 10 seconds, the forced cooling operation will start.

The forced cooling operation is used at the time of installation.

Only for authorized service personnel's use.

When the forced cooling operation starts by any chance, press the START/STOP but- ton to stop the operation.

3Indicator (Fig. 3)

4Remote Control Signal Receiver

5OPERATION Indicator Lamp (red)

6TIMER Indicator Lamp (green)

If the TIMER indicator lamp flashes when the timer is operating, it indicates that a fault has occurred with the timer setting (See Page 13 Auto Restart).

7COIL DRY Indicator Lamp (orange)

8Intake Grille (Fig. 4)

9Front Panel

0Air Filter

AAir Flow Direction Louver

BPower Diffuser

CRight-Left Louver

(behind Air Flow Direction Louver)

DDrain Hose

Fig. 5 Outdoor Unit

EIntake Port

FOutlet Port

GPipe Unit

HDrain port (bottom)

Refer to the folded out page on the cover.

Fig. 6 Remote Control Unit

ISLEEP button

JMASTER CONTROL button

KSET TEMP. button ( / )

LCOIL DRY button

MSignal Transmitter

NTIMER MODE button

OTIMER SET ( / ) button

PFAN CONTROL button

QSTART/STOP button

RSET button (Vertical)

SSET button (Horizontal)

TSWING button

URESET button

VTEST RUN button

This button is used when installing the conditioner, and should not be used un- der normal conditions, as it will cause the air conditioner’s thermostat function to op- erate incorrectly.

If this button is pressed during normal op- eration, the unit will switch to test opera- tion mode, and the Indoor Unit’s OPERA- TION Indicator Lamp and TIMER Indicator Lamp will begin to flash simultaneously.

To stop the test operation mode, press the START/STOP button to stop the air condi- tioner.

WCLOCK ADJUST button

XRemote Control Unit Display (Fig. 7)

YTransmit Indicator

ZClock Display

[ Operating Mode Display

\Timer Mode Display ] Fan Speed Display

` Temperature SET Display a COIL DRY Display

b SLEEP Display c SWING Display

En-3

Image 4
Contents Operating Manual Español Français EnglishContents Safety PrecautionsFeatures and Functions InverterName of Parts Indoor Unit Operating Control Panel Fig Manual Auto buttonPreparation Operation To Stop Operation Press the START/STOP button Q About Mode OperationAbout Auto Changeover Operation Timer Operation Sleep Timer Operation About the Sleep TimerManual Auto Operation During Heating operationAdjusting the Direction of AIR Circulation Types of Air flow Direction SettingSwing Operation Coil DRY OperationTo select Swing Operation Press the Swing button T About Swing OperationCleaning and Care Troubleshooting Symptom ProblemNormal FunctionEvent of Power Interruption Operating TipsOperation and Performance Auto RestartCooling Mode Dry Mode Heating Mode Outdoor temperature Temperature and Humidity RangeIndoor temperature ’essayez pas d’installer vous-même ce climatiseur Le personnel de service compétent en cas de réparationSommaire Précautions DE SécuritéCaractéristiques ET Fonctions InverseurNomenclature DES Organes Manual AutoPréparatifs Pour choisir le mode souhaité FonctionnementAppuyez sur la touche Master Control J Réglage du thermostat Appuyez sur la touche SET TEMP. KPropos du mode de fonctionnement Arrêt du climatiseur Appuyez sur la touche START/STOP QAppuyez sur la touche Timer Mode N pour Fonctionnement PAR Minuterie DE Programmation’heure d’arrêt et de mise en marche souhaitées Rêt OFF et la mise en marche on par minuterieFonctionnement Temporisé Fonctionnement MANUEL-AUTOMATIQUEChangement des réglages du minuterie Propos de la minuterie à temporisateurRéglage DE LA Direction DU Flux D’AIR Positions de réglage de direction du flux d’airPropos du mode oscillant Swing Fonctionnement OscillantFonctionnement DU Séchage DU Serpentin Propos du séchage du serpentinNettoyage ET Entretien Nettoyez la poussière avec un aspirateur ou en lavantNettoyez à l’eau Remettez la grille d’admissionGuide DE Dépannage Symptôme Problème VoyezFonctions NormalesConseils D’UTILISATION Fonctionnement et performanceRemise en marche automatique En cas de coupure de courantTempérature intérieure Environ 64 à 90 F Plage de température et d’humiditéEnviron 5 à 75 F Índice Precauciones DE SeguridadCaracterísticas Y Funciones InversorDenominación DE LOS Componentes Automática Sleep Pantalla de vaivén SwingPreparativos Funcionamiento Para seleccionar el modo de funcionamientoTrol J para seleccionar el modo deseado Para ajustar el termostatoNotassobreelfuncionamientodecambioautomáticoAUTOCHANGEOVER Notas sobre el funcionamiento de los modosFuncionamiento CON Temporizador Funcionamiento Manual Y Automático Para cambiar los ajustes del tiempoNotas sobre el temporizador de desconexión automática Sleep Durante el funcionamiento de calefacciónAjuste DE LA Dirección DE Circulación DEL Aire Tipos de ajustes de la dirección del flujo de aireFuncionamiento DE Vaivén Funcionamiento DE Deshumectación Coil DRYPara detener el funcionamiento de deshumectación Coil DRY Observaciones sobre el funcionamiento del vaivénLimpieza Y Mantenimiento Saque el polvo con una aspiradora o la VándoloLimpie con agua Colocación de la rejilla de entradaLocalización DE Averías Síntoma Problema Vea la PáginaFunciones Consejos Para EL Funcionamiento Funcionamiento y rendimientoReinicio automático En el caso de una interrupción de la alimentaciónMargen de temperatura y humedad Modo de refrigeraciónFuncionamiento de Temperatura exteriorPage

MW24Y3F specifications

The Friedrich MW24Y3F is a standout in the world of portable air conditioning units, designed for both residential and commercial applications. With its sleek design and advanced features, this model offers exceptional cooling capabilities while ensuring energy efficiency and user comfort.

One of the main features of the MW24Y3F is its powerful cooling capacity. With a BTU rating of 24,000, it is well-suited for larger rooms or open spaces, making it an ideal choice for users seeking effective temperature control without the noise and complexity of traditional central air conditioning systems. This unit can easily cool spaces of up to 1,500 square feet, providing a refreshing respite from sweltering heat.

The MW24Y3F employs cutting-edge technologies that enhance its performance and user experience. Notably, it incorporates inverter technology, allowing for more efficient energy consumption. By adjusting the compressor speed as per the cooling demand, it reduces energy usage while maintaining consistent temperatures. This translates to lower electricity bills and a reduced carbon footprint, making it an environmentally friendly choice.

Another significant characteristic is its user-friendly interface. The unit features a digital display and remote control, enabling users to adjust settings effortlessly from across the room. Additionally, the MW24Y3F includes a programmable timer, allowing for automatic operation based on the user’s schedule, further enhancing convenience.

The air conditioning unit also prioritizes air quality, integrating a multi-stage filtration system that captures dust, allergens, and other pollutants. This feature is particularly beneficial for those with respiratory issues or allergies, providing cleaner, healthier air in the living or work environment.

In terms of installation, the MW24Y3F is designed for flexibility. It can be set up as a window or portable unit, giving users options based on their property layout and personal preferences. Its compact size allows it to fit well in various spaces without compromising aesthetics.

In summary, the Friedrich MW24Y3F combines high cooling capacity, energy efficiency, user-friendly features, and air quality improvement technologies, making it an excellent choice for anyone looking to enhance their indoor climate control.