Lincoln Electric MIG-PAK 10 manual Learning to Weld Troubleshooting Welds

Page 44

LEARNING TO WELD

TROUBLESHOOTING WELDS

Good welds have excellent appearance.

To Eliminate Porosity (in order of importance):

1.Turn on gas supply, if used

2.Decrease voltage.

3.Increase stickout.

4.Increase WFS (wire feed speed).

5.Decrease drag angle.

6.Decrease travel speed.

NOTE: Always be sure the joint is free from moisture, oil, rust, paint or other contaminants.

To Eliminate a Ropy Convex Bead (in order of importance):

1.Increase voltage.

2.Decrease stickout.

3.Decrease WFS (wire feed speed.

4.Decrease travel speed.

5.Decrease drag angle.

6.Check for correct gas, if used.

APRENDIENDO A SOLDAR

LOCALIZACIÓN DE AVERÍAS EN SOLDADURAS

Las soldaduras adecuadas tienen una excelente apariencia.

Para Eliminar la Porosidad (por orden de importancia):

1.Si se utiliza, encienda el suministro de gas.

2.Disminuya el voltaje.

3.Aumente la punta electrizada de alambre.

4.Aumente la velocidad de alimentación de alambre (WFS).

5.Disminuya el ángulo de avance.

6.Disminuya la velocidad de avance.

NOTA: Siempre asegúrese de que la unión no esté húmeda, ni tenga aceite, óxido, pintura o cualquier otro contaminante.

Para Eliminar los Cordones Convexos (por orden de importancia):

1.Incremente el voltaje.

2.Disminuya la punta electrizada de alambre.

3.Disminuya la velocidad de alimentación de alambre (WFS).

4.Disminuya la velocidad de avance.

5.Disminuya el ángulo de avance.

6.Si se utiliza, verifique que el gas sea el correcto.

APPRENTISSAGE DU SOUDAGE

CORRECTION DES DÉFAUTS DE SOUDAGE

Les bonnes soudures ont un aspect excellent.

Pour éliminer les soufflures (par ordre d'importance) :

1.Ouvrir la bouteille de gaz (le cas échéant).

2.Diminuer la tension.

3.Augmenter la portée terminale.

4.Augmenter la vitesse de dévidage (du fil).

5.Diminuer l'angle longitudinal.

6.Diminuer la vitesse de déplacement.

NOTA: Toujours s'assurer que le joint est exempt d'humidité, d'huile, de rouille, de peinture ou d'autres contaminants.

Pour ne pas obtenir un cordon très convexe (par ordre d'importance):

1.Augmenter la tension.

2.Diminuer la portée terminale.

3.Diminuer la vitesse de dévidage.

4.Diminuer la vitesse de déplacement.

5.Diminuer l'angle longitudinal.

6.Vérifier que l'on utilise éventuellement le bon gaz.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Tabla DE Contenido Table DES MatièresElectricos Electric and Magnetic Fields may be dangerousPueden ser peligrosos LES Champs Électromagnétiques peuvent être dangereuxWelding Sparks can cause fire or explosion Electric Shock can kill El Electrochoque puede causar la muerteNunca sumergir el electrodo en agua para enfriarlo Ne jamais tremper lélectrode dans leau pour la refroidirLe soudage peut produire des fumées et des Fumes and Gases can be dangerousLES Fumées ET LES GAZ peu- vent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées Cylinder may explode if damagedLa Botella de gas puede explotar si está dañada Introductionintroducción General DescriptionDescripción General Description GénéraleFiche Technique Technical SpecificationsEspecificaciones Técnicas Components Componentes Composants Installation Instalación Work Clamp Installation Work Cable InstallationInstalacion DE LA Pinza DE Trabajo Instalacion DEL Cable DE TrabajoInstallation Instalacion GUN InstallationInstalacion DE LA Antorcha Montage DU PistoletGAS Connection Conexión DE GASRaccordement DE GAZ Lélectrode de soudage ne doit jamais toucher la bouteilleValve outlet Input Connections Code Requirements for Input ConnectionsConexiones DE LA Energía DE Alimentación Requerimientos DEL Codigo Para Conexiones DE EntradaSafety Precautions Operation OperacionPrecauciones DE Seguridad Electric Shock can killOperation FonctionnementControls and Settings Commandes ET RéglagesWelding Capability LimitationsOperation Operación Fonctionnement Ordre DES Opérations DE Soudage Operation Welding SequenceOperación Secuencia DE Operación DE Soldadura Friction Brake Adjustment Wire ThreadingAjuste DEL Freno DE Fricción Colocacion DEL AlambreWire Drive Feed Roll Can Accommodate Wire drive feed rollOver El Rodillo ImpulsorOperación Fonctionnement Remove gas nozzle and contact tip from end of gunPoignée du pistolet Diffuseur de gaz/tube contact Prête pour le soudageMaking a Weld Cómo Realizar UNA SoldaduraRéalisation Dune Soudure Beginning of this manualProcess Guidelines Instrucciones DEL ProcesoSoldadura CON Gmaw MIG Operation OperaciónfonctionnementWelding with Gmaw MIG Welding with Fcaw Innershield Soldadura CON Fcaw InnershieldOverload Protection Proteccion Contra SobrecargaLearning to Weld ARC-WELDING CircuitAprendiendo a Soldar Circuito DE Soldadura POR ArcoLarc DE Soudage Fcaw Autoprotégé SELF-SHIELDED Fcaw Welding ARCArco DE Soldadura Fcaw Tubular Autoprotegido Learning to Weld Aprendiendo a Soldar Gmaw MIG Welding ARCArco DE Soldadura Gmaw MIG Larc DE Soudage Gmaw MIGChoix DU Procédé Process SelectionSelección DEL Proceso Common Metals Joint Types and PositionsMetales Comunes Tipos DE Unión Y PosicionesButt Welds Soldadura a TopeSoudures bout à bout PenetrationSoudage en position verticale Welding In The Vertical PositionSoldadura en Posición Vertical Soudage à la verticale en descendant Vertical-down WeldingSoldadura Vertical Descendente Correct Welding Position Posición Correcta para SoldarLa bonne position de soudage Correct Way To Strike An ArcCorrect Electrical Stickout ESO Punta Electrizada de Alambre ESO CorrectaLa bonne portée terminale Correct Welding SpeedRecommandations utiles Voltage Setting Wire Feed Speed ooHelpful Hints Back-Stepping PracticeWelding Techniques for Gmaw MIG Process Técnicas DE Soldadura Para EL Proceso Gmaw MIGTechniques DE Soudage Pour LE Procédé Gmaw MIG Contact Tip Punta de contacto Tube contactPunta Portée terminale Correct Electrical Stickout ESOConsejos Útiles Recommandations utilesHelpful Hints Velocidad de alimentación De alambre oIo Lincolnweld 0.025 L-56Calibre 16 o 1/16 pulgadas Apprentissage DU Soudage Correction DES Défauts DE Soudage Learning to Weld Troubleshooting WeldsAprendiendo a Soldar Localización DE Averías EN Soldaduras To Correct Poor Penetration in order of importance To Eliminate Stubbing* in order of importanceProper Gun Handling Para Reducir las Salpicaduras en orden de importanciaAccessories AccessoiresOptional Accessories Accessoires EN OptionInnershield Fcaw Conversion Conversion Innershield FcawAccessorios Replacement PartsPartes DE Reemplazo Pièces DE RechangeMaintenance Safety Precautions Routine MaintenanceMantenimiento Precauciones DE Seguridad Mantenimiento DE RutinaMaintenance GUN and Cable For Magnumtm 100L GUN Maintenance EntretienContact Tip Cable Liner Drive Roll Rodillo ImpulsorCambio DEL Rodillo Impulsor Remplacement DU Galet DentraînementChanging Drive Roll Cambio DE LA Guía DE Alambre Remplacement DU Conduit IntérieurChanging Liner Troubleshooting Avec votre Service APRÈS-VENTE Local Agréé PARLocalización DE AVERíAS DépannageArc is unstable Poor starting El arco es inestable Arranque deficienteLarc est instable Mauvais amorçage SuivreMIG PAK 10 Wiring Diagram Parts Partes PiècesMIG-PAK MIG-PAK MIG-PAK Need Welding Training? How To Read Shop DrawingsNew Lessons in Arc Welding Use ventilation or exhaust to GroundProtéjase los ojos, los oídos y el Fuera del área de trabajo Cuerpo PiraciónGuardas quitadas TienProtection enlevés Strom vor Wartungsarbeiten Nen Maschine anhalten Betrieb setzenWorlds Leader in Welding and Cutting Products

MIG-PAK 10 specifications

The Lincoln Electric MIG-PAK 10 is a versatile and user-friendly MIG welding machine tailored for light industrial applications and DIY enthusiasts. This compact welder is designed for both professionals and hobbyists, offering a perfect blend of performance and portability. It is particularly suitable for welding light to medium-gauge steel, stainless steel, and aluminum.

One of the standout features of the MIG-PAK 10 is its economy of size without compromising on power. Weighing in at just around 40 pounds, it is easily transportable, making it a practical choice for on-site jobs or small workshops. Its compact dimensions allow it to fit into tight spaces, facilitating accessibility for various welding tasks.

The MIG-PAK 10 employs a built-in gas solenoid that facilitates gas shielding for improved arc stability and weld quality. It is compatible with both shielding gas and flux-cored wire, offering flexibility depending on the application requirements and working environment. This dual capability is particularly beneficial for outdoor welding, where wind can disrupt gas shielding.

Lincoln Electric has integrated an adjustable output that offers a wide range of voltage settings, allowing users to fine-tune their settings for different materials and thicknesses. This feature, accompanied by a smooth and stable arc, contributes to high-quality welds and ease of operation.

Ease of use is further enhanced by the machine’s simple control panel, which features clear indicators and settings. Novice welders will appreciate the intuitive layout, while experienced users will value the precision controls for intricate tasks.

Another key technology utilized in the MIG-PAK 10 is Lincoln Electric’s professional-grade drive system, which ensures reliable wire feed performance. This system minimizes downtime and improves welding efficiency by reducing the chances of wire tangling or feeding issues.

Finally, the MIG-PAK 10 is constructed with durability in mind. Its robust casing is designed to withstand the rigors of welding environments, ensuring longevity and consistent performance.

In summary, the Lincoln Electric MIG-PAK 10 is a well-rounded MIG welder suitable for various welding needs. Its exceptional portability, dual wire feeding options, adjustable output, user-friendly controls, and sturdy construction make it a compelling choice for both beginners and professionals in the welding industry.
Top Page Image Contents