Hitachi C 10FCD instruction manual Before Using

Page 12

English

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied wrench, tighten the bolt on the arbor shaft to secure the saw blade. For details, see Fig. 36-a, Fig. 36-b and Fig. 36-c in the section on “SAW BLADE MOUNTING AND DISMOUNTING”.

5. Check the blade guards for proper operation.

Blade Guard (Metal)

Blade guards are designed to protect the operator from coming into contact with the saw blade during operation of the tool. Always check that the blade guard (plastic) moves smoothly and covers the saw blade properly.

Blade Guard (Plastic)

Fig. 8

WARNING: Never operate the power tool if the blade guard (plastic) does not function smoothly.

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position before using the power tool (see Fig. 36-a).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Confirm that the saw blade can be lowered 1-1/32" to 1-3/32" (26 mm to 28 mm) below the table insert. For details, see the section on “Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if it is faulty.

9. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

10. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.

11. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably unstable; otherwise vibrations might occur and cause an accident.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Avertissement AdvertenciaContents Meanings of Signal Words Inportant Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications 10FCDInstallation ApplicationsPreparation Before Operation Installing the extension stay Releasing the plunger handleBefore Using Before Cutting Cutting a groove on the table insertChecking the saw blade lower limit position Oblique angleInstalling the extension wings Optional accessory Practical ApplicationsSecuring the workpiece Switch operation Using the vise assembly Standard accessoryUsing the vise assembly Optional accessory Miter cutting proceduresCutting Operation Bevel cutting procedures Compound cutting proceduresCrown molding cutting procedures For miter cut settingEnglish How to use the dust bag Standard accessory Cutting easily-deformed materials, such as aluminum sashSAW Blade Mounting and Dismounting Mounting the saw bladeMaintenance and Inspection Overload Protective Device for POLY-V-BELTService and Repairs Informations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Sécurité Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utilisation DUN Cordon DE RallongeDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications CordonPréparation Avant L’UTILISATION Installation de la traverse de rallonge Libérer la goupille de verrouillageAvant L’UTILISATION Avant LA Coupe Coupe d’une encoche dans la plaque d’insertionVérification de la position de limite inférieure de la lame Angle obliqueInstallation des servantes accessoires en option Applications PratiquesFixation de la pièce Utilisation de l’ensemble d’étau accessoire standard Fonctionnement de l’interrupteurUtilisation de l’ensemble d’étau accessoire en option CoupeProcédure de coupe d’onglet Procédure de coupe de biseau Procédures de coupe mixteProcédures de coupe de corniche complexe Réglage d’une coupe d’ongletDroite 33,9 Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA Lame Installation de la lameEntretien ET Inspection Retrait de la lameInspection de la lame Inspecter les balais carbone et FigService APRÈS-VENTE ET Réparations Información Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilización DE UN Cable ProlongadorAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Aplicaciones Preparativos Previos a LA OperaciónInstalación Liberación del mango de émbolo Instalación del soporte de extensiónAntes DE LA Utilización Antes DEL Corte Corte de ranura en un inserto de la mesaÁngulo oblicuo Aplicaciones Prácticas Inmovilización de la pieza de trabajoInstalación de los soportes de extensión Accesorio opcional Operación del interruptor Operación de corte Procedimiento de corte de ingletesProcedimientos de corte en bisel Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesIzquierda 31,6˚ Izquierda 33,9˚ derecha 33,9˚ Forma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE Sierra Montaje de la hoja de sierraMantenimiento E Inspección Desmontaje de la hoja de sierraInspección de la hoja de sierra Inspeccion las de escobillas Figs yServicio Y Reparaciones Page Page Page Page Page Page Hitachi Koki Canada Co
Top Page Image Contents