Hitachi C 10FCD instruction manual Switch operation, Using the vise assembly Standard accessory

Page 15

English

1. Switch operation

Switch

Lock

Hole

Trigger

Switch

Fig. 17

The switch lock is designed to prevent inadvertent operation of the power tool.

To operate the power tool, it is necessary to first push up the switch lock as shown in Fig. 17.

The trigger switch will not operate unless the switch lock has been pushed up. When the trigger switch is released, the power goes off and the switch lock automatically returns to its initial position, locking the trigger switch.

WARNING: This will ensure that the power tool cannot be turned on accidentally or by someone (especially a child) who is not qualified to use the power tool.

To prevent unauthorized operation of this tool, insert a padlock through the hole in the switch trigger.

2. Using the vise assembly (Standard accessory)

Vise

Assembly

Support

	Base	5 mm
	Base	Clamp Bolt
		Clamp Bolt
		Fig. 18

Vise

Assembly

Support

Fence

5mm Clamp Bolt

(1)The vise assembly can be mounted on either the left side base or the right side base, and can be raised or lowered according to the height of the workpiece.

qInsert support of vise assembly into the hole located on either the left side base or the right side base.

wThen tighten 5 mm clamp bolt as shown in Fig. 18.

NOTE: The support has two locking grooves into which the tip of the 5 mm clamp bolt is designed to fit, to lock the vise assembly in the desired position.

(2)The vise assembly can be mounted on either the left side fence or the right side fence, and can be raised or lowered according to the height of the workpiece.

qInsert support of vise assembly into the hole located on either the left side fence or the right side fence.

wThen tighten 5 mm clamp bolt as shown in Fig. 19.

Fig. 19

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the vise assembly when it is lowered for cutting. If there is any danger that it may do so, loosen the 5

mmclamp bolt slightly and move the vise assembly to a position where it will not contact the saw blade.

15

Image 15

Contents Advertencia AvertissementContents Meanings of Signal Words Inportant Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts USE Proper Extension Cord Replacement PartsDouble Insulation for Safer Operation Name of Parts Operation and Maintenance10FCD SpecificationsInstallation ApplicationsPreparation Before Operation Releasing the plunger handle Installing the extension stayBefore Using Oblique angle Before CuttingCutting a groove on the table insert Checking the saw blade lower limit positionInstalling the extension wings Optional accessory Practical ApplicationsSecuring the workpiece Using the vise assembly Standard accessory Switch operationUsing the vise assembly Optional accessory Miter cutting proceduresCutting Operation For miter cut setting Bevel cutting proceduresCompound cutting procedures Crown molding cutting proceduresEnglish Cutting easily-deformed materials, such as aluminum sash How to use the dust bag Standard accessoryMounting the saw blade SAW Blade Mounting and DismountingOverload Protective Device for POLY-V-BELT Maintenance and InspectionService and Repairs Informations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Sécurité Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utilisation DUN Cordon DE RallongeDouble Isolation Pour UN Fonctionnement Plus SUR NOM DES Pièces Utilisation ET EntretienCordon SpécificationsPréparation Avant L’UTILISATION Libérer la goupille de verrouillage Installation de la traverse de rallongeAvant L’UTILISATION Angle oblique Avant LA CoupeCoupe d’une encoche dans la plaque d’insertion Vérification de la position de limite inférieure de la lameInstallation des servantes accessoires en option Applications PratiquesFixation de la pièce Fonctionnement de l’interrupteur Utilisation de l’ensemble d’étau accessoire standardUtilisation de l’ensemble d’étau accessoire en option CoupeProcédure de coupe d’onglet Réglage d’une coupe d’onglet Procédure de coupe de biseauProcédures de coupe mixte Procédures de coupe de corniche complexeDroite 33,9 Utilisation du sac à copeaux Accessoire standard Installation de la lame Installation ET Retrait DE LA LameInspecter les balais carbone et Fig Entretien ET InspectionRetrait de la lame Inspection de la lameService APRÈS-VENTE ET Réparations Información Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilización DE UN Cable ProlongadorAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura DE Partes Operación Y MantenimientoEspecificaciones Aplicaciones Preparativos Previos a LA OperaciónInstalación Instalación del soporte de extensión Liberación del mango de émboloAntes DE LA Utilización Antes DEL Corte Corte de ranura en un inserto de la mesaÁngulo oblicuo Aplicaciones Prácticas Inmovilización de la pieza de trabajoInstalación de los soportes de extensión Accesorio opcional Operación del interruptor Procedimiento de corte de ingletes Operación de cortePara el ajuste de corte de ingletes Procedimientos de corte en biselProcedimientos de corte compuesto Procedimientos de corte con moldura en vérticeIzquierda 31,6˚ Izquierda 33,9˚ derecha 33,9˚ Forma de utilizar la bolsa para el polvo Accesorio estándar Montaje de la hoja de sierra Montaje Y Desmontaje DE LA Hoja DE SierraInspeccion las de escobillas Figs y Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la hoja de sierraServicio Y Reparaciones Page Page Page Page Page Page Hitachi Koki Canada Co