Hitachi C 10FCD instruction manual SAW Blade Mounting and Dismounting, Mounting the saw blade

Page 20

English

SAW BLADE MOUNTING AND DISMOUNTING

WARNING: To prevent an accident or personal injury, always turn off the trigger switch and disconnect the power plug from the receptacle before removing or installing a saw blade.

1.Mounting the saw blade

(1)Rotate blade guard (plastic), to top position.

(2)Loosen 5 mm screw to free cutter shaft guard.

And rotate cutter shaft guard to the up position as shown in Fig. 36-b. At that time, the blade guard (plastic) move together.

(3)Press in spindle lock and loosen bolt with wrench.

Since the bolt is left-hand threaded, loosen by turning it to the right as shown in Fig. 36-b.

NOTE: If the spindle lock cannot be easily pressed in to lock the arbor shaft, turn the bolt with wrench while applying pressure on the spindle lock.

The arbor shaft is locked when the spindle lock is pressed inward.

(4) Remove the bolt and arbor collar.

Spindle

Lock

		Fig. 36-a
	Saw Blade	Arbor	mm)
		Collar	(15.9
	Blade Washer	Collar	(15.9
	Blade Washer	Collar	5/8"
	Bolt		5/8"
	Bolt

Blade Guard (Plastic)

Cutter Shaft

Guard

Tighten

5 mm Screw

Up

Arbor Collar

Arbor Shaft	Loosen
Arbor Shaft
	Wrench
	Bolt
	Saw Blade

Spot Facing

Fig. 36-b

Fig. 36-c

(5) Mount the saw blade.

WARNING: When mounting the saw blade, confirm that the rotation indicator mark on the saw blade and the rotation direction of the blade guard (metal) are properly matched.

(6)Thoroughly clean collar, arbor collar, blade washer (confirm mounting direction) and the bolt, and install them onto the arbor shaft as shown in Fig. 36-c.

(7)Press in the spindle lock and tighten the bolt by turning it to the left by wrench as indicated in Fig. 36-b.

CAUTION: * Confirm that the spindle lock has returned to the retract position after installing or removing the saw blade.

*Tighten the bolt so it does not come loose during operation.

Confirm the bolt has been properly tightened before the power tool is started.

(8)Rotate the cutter shaft guard to the initial position and tighten 5 mm screw.

(9)Place blade guard (plastic) in the down position.

20

Image 20

Contents Avertissement AdvertenciaContents Important Information Meanings of Signal WordsInportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications 10FCDPreparation Before Operation InstallationApplications Installing the extension stay Releasing the plunger handleBefore Using Before Cutting Cutting a groove on the table insertChecking the saw blade lower limit position Oblique angleSecuring the workpiece Installing the extension wings Optional accessoryPractical Applications Switch operation Using the vise assembly Standard accessoryCutting Operation Using the vise assembly Optional accessoryMiter cutting procedures Bevel cutting procedures Compound cutting proceduresCrown molding cutting procedures For miter cut settingEnglish How to use the dust bag Standard accessory Cutting easily-deformed materials, such as aluminum sashSAW Blade Mounting and Dismounting Mounting the saw bladeMaintenance and Inspection Overload Protective Device for POLY-V-BELTService and Repairs Consignes DE Sécurité Relatives AUX Outils Électriques Informations ImportantesSignification DES Mots D’AVERTISSEMENT Français Consignes de sécurité spéciales pour cet outil électrique Français Double Isolation Pour UN Fonctionnement Plus SUR Pieces DE RechangeUtilisation DUN Cordon DE Rallonge Utilisation ET Entretien NOM DES PiècesSpécifications CordonPréparation Avant L’UTILISATION Installation de la traverse de rallonge Libérer la goupille de verrouillageAvant L’UTILISATION Avant LA Coupe Coupe d’une encoche dans la plaque d’insertionVérification de la position de limite inférieure de la lame Angle obliqueFixation de la pièce Installation des servantes accessoires en optionApplications Pratiques Utilisation de l’ensemble d’étau accessoire standard Fonctionnement de l’interrupteurProcédure de coupe d’onglet Utilisation de l’ensemble d’étau accessoire en optionCoupe Procédure de coupe de biseau Procédures de coupe mixteProcédures de coupe de corniche complexe Réglage d’une coupe d’ongletDroite 33,9 Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA Lame Installation de la lameEntretien ET Inspection Retrait de la lameInspection de la lame Inspecter les balais carbone et FigService APRÈS-VENTE ET Réparations Normas DE Seguridad Para LAS Herramientas Eléctricas Información ImportanteSignificado DE LAS Palabras Clave Español Español Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Piezas DE ReemplazoUtilización DE UN Cable Prolongador Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Instalación AplicacionesPreparativos Previos a LA Operación Liberación del mango de émbolo Instalación del soporte de extensiónAntes DE LA Utilización Ángulo oblicuo Antes DEL CorteCorte de ranura en un inserto de la mesa Instalación de los soportes de extensión Accesorio opcional Aplicaciones PrácticasInmovilización de la pieza de trabajo Operación del interruptor Operación de corte Procedimiento de corte de ingletesProcedimientos de corte en bisel Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesIzquierda 31,6˚ Izquierda 33,9˚ derecha 33,9˚ Forma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE Sierra Montaje de la hoja de sierraMantenimiento E Inspección Desmontaje de la hoja de sierraInspección de la hoja de sierra Inspeccion las de escobillas Figs yServicio Y Reparaciones Page Page Page Page Page Page Hitachi Koki Canada Co