Fluke 7350 specifications Tutorial, Main Menu

Page 27

Local Operation 4

Tutorial

Tutorial

To begin the tutorial, first verify that the Calibrator is powered-up and that the pneumatic connections have been completed. The Calibrator should display a screen similar to the one shown below. (The right hand side of the display should show the options). At power up, there may be errors relating to the default settings. If an error message is displayed in red at the bottom of the screen, press [F6], then press PREVIOUS. If multiple errors exist, you will need to press the [F6] key multiple times to clear all of the errors.

gld04.bmp

Figure 4-3. Main Menu

Figure 4-3 shows the Main Menu. It is at the top level of the menu tree (see Figure 4-2) and all descriptions in this manual start from this point. The double sized numbers in the top center of the display shows the current measured pressure (0.00 psi diff). The upper left corner shows the current mode of the Calibrator (MEASURE, CONTROL or VENT). The right side of the screen shows a bar graph displaying the current pressure relative to a user-configurable full-scale value. Below the pressure is the pressure control set-point; below this is the difference between the set-point and the actual value. Below this is a numeric scratchpad for entering a new set-point value. The highlighted label on the right hand side of the screen displays the current assignments of the function keys [F1] through [F6] that are located beside the display.

1.Change the pressure units. The units are changed by selecting the UNITS key on the keypad.

gld05.bmp & gld06.bmp

Figure 4-4. Units - Menu

4-3

Image 27
Contents Ruska Limited Warranty and Limitation of Liability Table of Contents Theory of Operation Remote Operation Preparation for Storage and Shipment List of Tables Ruska List of Figures Viii General Information How to Contact FlukeGeneral Information IntroductionSafety Information Features Symbols Used in this ManualEasily Programmable Power-On Self TestAutomatic Zero Adjust Ease of OperationRuska 7350 Options List Part Number Standard Equipment & OptionsRuska Back Plane Board Power SupplyTheory of Operation Electronics SectionRuska 7350 Block Diagram IEEE-488 Interface Front PanelMotor Controller Gearmotor Pneumatic Module76xx Interface Board Pneumatic PumpTest Port Electronics RegulatorDome Regulator System TransducerRuska Unpacking the Ruska InstallationPowering Up the Ruska Pneumatic ConnectionsDrive Air Supply Port Function Keys Local OperationLocal Operation Numeric KeypadMenu Tree Cancel, PreviousMain Menu TutorialMain Menu Entering Pressure Selecting Mode of Operation Tare ModeSelecting Language Triple Range Optional Setting the Pressure Set-PointMain Menu Controlling PressureStep/Jog VentMenu Menu SetupAuto Vent Menu Setup LimitsHigh Limit Low LimitControl Band Slew Limit AccessMenu Setup User Slew RateGas Head Pressure Correction Step SizeBar Graph Maximum Ready ToleranceKey Click Menu Setup UnitsPressure Filter Changing the Number of Decimals13. Menu Setup Units Edit Name Menu Protocol Menu Setup RemoteMenu Setup System Gpib AddressMenu Calibrate ResetCalibration Password Date/TimePreparing to Program Menu Program Storing a Sequence in MemoryMode of Entry MaxTimeEntering a New Program 17. Menu Program Edit Menu 18. Menu Program Edit Auto Menu Automatically Generating a ProgramChanging an Existing Program Changing the Name of a Program20. Menu Program Edit Menu Changing the Configuration Stored with a ProgramRunning a Program 21. Menu Program Config MenuMenu Test Sweep Test Menu TestMenu Test Remote Test Menu Test Self Test26. Menu Test Shop1 Menu Menu Test Shop1Menu Display Blank Menu DisplayRuska IEEE-488 Remote OperationRemote Operation CapabilitiesRS-232 Remote/Local OperationScpi Response Format ConfigurationScpi Command Format Device MessagesScpi Command Summary ANSI/IEEE 488.2-1987 Command SummaryMODE? List Example Scpi CommandsScpi Status Registers Interface Panel Emulation Serial Operation Ruska Observing the Software Version Number MaintenancePreventive Maintenance Observing the Ruska 7350’s Full Scale RatingCalibration Processor BatteryPreparation Calibration Instructions Single SensorStoring the Coefficients Zeroing Editing the Calibration CoefficientsCleaning Ruska 7350 Pump LubricationFuse Preparation for Storage and Shipment Disconnection InstructionsPacking Instructions Fluke Calibration Westpark Drive HOUSTON, TX USA Packing the Calibrator Shipping Instructions7350 Accuracy Summary of SpecificationsSpecifications Summary of Specifications Ruska Summary of Error Messages Summary of Error MessagesSetpoint is out of range