Fluke 7350 specifications Menu Setup Units Edit Name Menu

Page 38

RUSKA 7350

Users Manual

1.The pressure units are defined from the Menu Units Define. From the Main Menu (press PREVIOUS until the Main Menu appears) press Menu [F6 ⎢Setup [F2] ⎢Units [F3].

2.Use the rotary knob to highlight the desired user-defined unit, and then select the Edit Name [F1] function key.

3.The following sequence is used to change the name of the selected unit.

a.Use the < [F4] or > [F5] key to highlight the desired character in the matrix.

b.Use the rotary knob to change the character.

c.Repeat steps a and b until the desired name is entered. Press the Clear key to start over.

d.Press the Done [F6] key when the name change is completed.

gld15.bmp

Figure 4-13. Menu Setup Units Edit Name - Menu

4.Use the rotary knob to highlight the desired user-defined unit that has just been renamed.

5.Use the numeric keypad to enter the conversion factor and press ENTER to accept.

6.Press PREVIOUS three times to return to the Main Menu. The new unit definition may now be selected using the Units key.

4-14

Image 38

Contents Ruska Limited Warranty and Limitation of Liability Table of Contents Theory of Operation Remote Operation Preparation for Storage and Shipment List of Tables Ruska List of Figures Viii Introduction How to Contact FlukeGeneral Information General InformationSafety Information Symbols Used in this Manual FeaturesEase of Operation Power-On Self TestAutomatic Zero Adjust Easily ProgrammableStandard Equipment & Options Ruska 7350 Options List Part NumberRuska Electronics Section Power SupplyTheory of Operation Back Plane BoardRuska 7350 Block Diagram Motor Controller IEEE-488 InterfaceFront Panel Pneumatic Pump Pneumatic Module76xx Interface Board GearmotorSystem Transducer Electronics RegulatorDome Regulator Test PortRuska Installation Unpacking the RuskaDrive Air Supply Port Powering Up the RuskaPneumatic Connections Numeric Keypad Local OperationLocal Operation Function KeysCancel, Previous Menu TreeTutorial Main MenuMain Menu Entering Pressure Selecting Language Selecting Mode of OperationTare Mode Controlling Pressure Setting the Pressure Set-PointMain Menu Triple Range OptionalVent Step/JogMenu Setup MenuLow Limit Menu Setup LimitsHigh Limit Auto VentControl Band Slew Rate AccessMenu Setup User Slew LimitReady Tolerance Step SizeBar Graph Maximum Gas Head Pressure CorrectionChanging the Number of Decimals Menu Setup UnitsPressure Filter Key Click13. Menu Setup Units Edit Name Menu Gpib Address Menu Setup RemoteMenu Setup System ProtocolDate/Time ResetCalibration Password Menu CalibrateMenu Program Storing a Sequence in Memory Preparing to ProgramEntering a New Program Mode of EntryMaxTime 17. Menu Program Edit Menu Automatically Generating a Program 18. Menu Program Edit Auto MenuChanging the Name of a Program Changing an Existing ProgramChanging the Configuration Stored with a Program 20. Menu Program Edit Menu21. Menu Program Config Menu Running a ProgramMenu Test Menu Test Sweep TestMenu Test Self Test Menu Test Remote TestMenu Test Shop1 26. Menu Test Shop1 MenuMenu Display Menu Display BlankRuska Capabilities Remote OperationRemote Operation IEEE-488Remote/Local Operation RS-232Device Messages ConfigurationScpi Command Format Scpi Response FormatANSI/IEEE 488.2-1987 Command Summary Scpi Command SummaryMODE? Example Scpi Commands ListScpi Status Registers Interface Panel Emulation Serial Operation Ruska Observing the Ruska 7350’s Full Scale Rating MaintenancePreventive Maintenance Observing the Software Version NumberProcessor Battery CalibrationCalibration Instructions Single Sensor PreparationStoring the Coefficients Editing the Calibration Coefficients ZeroingFuse CleaningRuska 7350 Pump Lubrication Packing Instructions Preparation for Storage and ShipmentDisconnection Instructions Fluke Calibration Westpark Drive HOUSTON, TX USA Shipping Instructions Packing the Calibrator7350 Summary of Specifications AccuracySpecifications Summary of Specifications Ruska Summary of Error Messages Summary of Error MessagesSetpoint is out of range