Fluke 7350 Menu Setup Remote, Gpib Address, Protocol, Serial Interface Set-Up, Menu Setup System

Page 39

Local Operation 4

Menu

Menu Setup — Remote

The Menu Setup Remote screen is where the remote communication interface is set-up.

gld16.bmp

Figure 4-14. Menu Setup Remote - Menu

GPIB Address

Sets the IEEE-488 interface address.

Protocol

The Protocol defines which protocol should be used by the remote interface. The options are Standard Communication for Programmable Instruments (SCPI) which is the standard interface, 6000 to emulate the Series 6000 pressure controller, and 510 to emulate the Model 510 pressure controller. When using the SCPI interface, the RUSKA 7350 will emulate the 7010 and 7215 series controllers.

Serial Interface Set-Up

The operator can set-up the Baud Rate, Data Bits, Parity, and Stop Bits for the Serial Interface.

Menu Setup — System

The System Menu identifies the Software release version that is being operated in the Calibrator. It also stores and allows the operator to edit the Date and Time.

gld17.bmp

Figure 4-15. Menu Setup System - Menu

4-15

Image 39

Contents Ruska Limited Warranty and Limitation of Liability Table of Contents Theory of Operation Remote Operation Preparation for Storage and Shipment List of Tables Ruska List of Figures Viii General Information How to Contact FlukeGeneral Information IntroductionSafety Information Features Symbols Used in this ManualEasily Programmable Power-On Self TestAutomatic Zero Adjust Ease of OperationRuska 7350 Options List Part Number Standard Equipment & OptionsRuska Back Plane Board Power SupplyTheory of Operation Electronics SectionRuska 7350 Block Diagram IEEE-488 Interface Front PanelMotor Controller Gearmotor Pneumatic Module76xx Interface Board Pneumatic PumpTest Port Electronics RegulatorDome Regulator System TransducerRuska Unpacking the Ruska InstallationPowering Up the Ruska Pneumatic ConnectionsDrive Air Supply Port Function Keys Local OperationLocal Operation Numeric KeypadMenu Tree Cancel, PreviousMain Menu TutorialMain Menu Entering Pressure Selecting Mode of Operation Tare ModeSelecting Language Triple Range Optional Setting the Pressure Set-PointMain Menu Controlling PressureStep/Jog VentMenu Menu SetupAuto Vent Menu Setup LimitsHigh Limit Low LimitControl Band Slew Limit AccessMenu Setup User Slew RateGas Head Pressure Correction Step SizeBar Graph Maximum Ready ToleranceKey Click Menu Setup UnitsPressure Filter Changing the Number of Decimals13. Menu Setup Units Edit Name Menu Protocol Menu Setup RemoteMenu Setup System Gpib AddressMenu Calibrate ResetCalibration Password Date/TimePreparing to Program Menu Program Storing a Sequence in MemoryMode of Entry MaxTimeEntering a New Program 17. Menu Program Edit Menu 18. Menu Program Edit Auto Menu Automatically Generating a ProgramChanging an Existing Program Changing the Name of a Program20. Menu Program Edit Menu Changing the Configuration Stored with a ProgramRunning a Program 21. Menu Program Config MenuMenu Test Sweep Test Menu TestMenu Test Remote Test Menu Test Self Test26. Menu Test Shop1 Menu Menu Test Shop1Menu Display Blank Menu DisplayRuska IEEE-488 Remote OperationRemote Operation CapabilitiesRS-232 Remote/Local OperationScpi Response Format ConfigurationScpi Command Format Device MessagesScpi Command Summary ANSI/IEEE 488.2-1987 Command SummaryMODE? List Example Scpi CommandsScpi Status Registers Interface Panel Emulation Serial Operation Ruska Observing the Software Version Number MaintenancePreventive Maintenance Observing the Ruska 7350’s Full Scale RatingCalibration Processor BatteryPreparation Calibration Instructions Single SensorStoring the Coefficients Zeroing Editing the Calibration CoefficientsCleaning Ruska 7350 Pump LubricationFuse Preparation for Storage and Shipment Disconnection InstructionsPacking Instructions Fluke Calibration Westpark Drive HOUSTON, TX USA Packing the Calibrator Shipping Instructions7350 Accuracy Summary of SpecificationsSpecifications Summary of Specifications Ruska Summary of Error Messages Summary of Error MessagesSetpoint is out of range