Fluke specifications Standard Equipment & Options, Ruska 7350 Options List Part Number

Page 15

General Information 1

Standard Equipment & Options

Standard Equipment & Options

A standard pneumatic RUSKA 7350 comes with this manual, a power cord, a grease gun and grease. The standard pneumatic RUSKA 7350 is fully functional, but the following options are also available.

IEEE-488 Interface: All models of the RUSKA 7350 have an IEEE-488 (GPIB) card. The user’s computer communicates with the RUSKA 7350 through the Standard Commands for Programmable Instruments (SCPI) protocol. In addition, software written for the Series 7000 CALIBRATOR and Series 6000 DPG is fully compatible with the RUSKA 7350.

Additional Power Cords: Additional power cords are available for most countries of the world.

Table 1-2. RUSKA 7350 - Options List

Option	Part Number

Communication Software	Contact Fluke

User’s Manual	3952249

Power Cord, USA and Canada	284174

Power Cord, Central Europe	769422

Power Cord, India	782771

Power Cord, Japan	3898323

Power Cord, Australia/New Zealand	658641

Battery	2135249

1-5

Image 15

Contents Ruska Limited Warranty and Limitation of Liability Table of Contents Theory of Operation Remote Operation Preparation for Storage and Shipment List of Tables Ruska List of Figures Viii General Information How to Contact FlukeGeneral Information IntroductionSafety Information Features Symbols Used in this ManualEasily Programmable Power-On Self TestAutomatic Zero Adjust Ease of OperationRuska 7350 Options List Part Number Standard Equipment & OptionsRuska Back Plane Board Power SupplyTheory of Operation Electronics SectionRuska 7350 Block Diagram IEEE-488 Interface Front PanelMotor Controller Gearmotor Pneumatic Module76xx Interface Board Pneumatic PumpTest Port Electronics RegulatorDome Regulator System TransducerRuska Unpacking the Ruska InstallationPowering Up the Ruska Pneumatic ConnectionsDrive Air Supply Port Function Keys Local OperationLocal Operation Numeric KeypadMenu Tree Cancel, PreviousMain Menu TutorialMain Menu Entering Pressure Selecting Mode of Operation Tare ModeSelecting Language Triple Range Optional Setting the Pressure Set-PointMain Menu Controlling PressureStep/Jog VentMenu Menu SetupAuto Vent Menu Setup LimitsHigh Limit Low LimitControl Band Slew Limit AccessMenu Setup User Slew RateGas Head Pressure Correction Step SizeBar Graph Maximum Ready ToleranceKey Click Menu Setup UnitsPressure Filter Changing the Number of Decimals13. Menu Setup Units Edit Name Menu Protocol Menu Setup RemoteMenu Setup System Gpib AddressMenu Calibrate ResetCalibration Password Date/TimePreparing to Program Menu Program Storing a Sequence in MemoryMode of Entry MaxTimeEntering a New Program 17. Menu Program Edit Menu 18. Menu Program Edit Auto Menu Automatically Generating a ProgramChanging an Existing Program Changing the Name of a Program20. Menu Program Edit Menu Changing the Configuration Stored with a ProgramRunning a Program 21. Menu Program Config MenuMenu Test Sweep Test Menu TestMenu Test Remote Test Menu Test Self Test26. Menu Test Shop1 Menu Menu Test Shop1Menu Display Blank Menu DisplayRuska IEEE-488 Remote OperationRemote Operation CapabilitiesRS-232 Remote/Local OperationScpi Response Format ConfigurationScpi Command Format Device MessagesScpi Command Summary ANSI/IEEE 488.2-1987 Command SummaryMODE? List Example Scpi CommandsScpi Status Registers Interface Panel Emulation Serial Operation Ruska Observing the Software Version Number MaintenancePreventive Maintenance Observing the Ruska 7350’s Full Scale RatingCalibration Processor BatteryPreparation Calibration Instructions Single SensorStoring the Coefficients Zeroing Editing the Calibration CoefficientsCleaning Ruska 7350 Pump LubricationFuse Preparation for Storage and Shipment Disconnection InstructionsPacking Instructions Fluke Calibration Westpark Drive HOUSTON, TX USA Packing the Calibrator Shipping Instructions7350 Accuracy Summary of SpecificationsSpecifications Summary of Specifications Ruska Summary of Error Messages Summary of Error MessagesSetpoint is out of range