Panasonic EY7411  Control Panel, Reference for Adjusting Torque, Screw count function

Page 8

Reference for Adjusting Torque

Setting

Torque

Use

1Approx: 0.29 N·m

(3.0 kgf-cm or 2.6 in-lbs)

5Approx: 0.82 N·m

(8.4 kgf-cm or 7.3 in-lbs)

9

Approx: 1.35 N·m

 

(13.8 kgf-cm or 12.0 in-lbs) For driving

 

 

 

screws

13

Approx: 1.88 N·m

(19.2 kgf-cm or 16.6 in-lbs)

 

 

 

17Approx: 2.41 N·m

(24.6 kgf-cm or 21.3 in-lbs)

21Approx: 2.94 N·m

(30.0 kgf-cm or 26.0 in-lbs)

For power-

Approx: 4.4 N·m ful driving (45.0 kgf-cm or 39.0 in-lbs) screws and

drilling

●When using at high speeds, set the clutch at 10 or below. (Operation stops at the maximum torque of 1.5 N·m (15 kgf-cm) when the scale is higher.)

●The auto shut-off function may become inoperable at high clutch settings when battery power drops. Recharge the battery in that case.

NOTE:

The chart is only a reference. The torque settings may differ by materi- als, types of screws, etc. Please test it at your own conditions before use.

Control Panel

Manufacturer settings upon shipment

●Count system: Count down system

●Count setting value: 99

●Buzzer sound pitch: b1 (Low sound)

●Double tightening counting preven- tion count time: 0 (OFF)

●Hold switch: Released

Please set the settings according to conditions of use.

Screw count function

●Counts the number of auto stops. (Counts the number of screws driven)

●The count method can be selected from “UP” or “DOWN”.

●When the set number of screws to be driven is reached, a buzzer sounds and the count value is reset.

●The buzzer sound can be selected from 3 types of sound.

●Double tightening counting prevention function

Work (double tightening and screw driving confirmation, etc.) that began within the set time is not counted after the driven screws are counted.

Count display lamp

Count system display lamp

Lock button

Switch

Hold switch

Release

ON

Starting the control panel

1.Release the hold switch.

2.To illuminate the control panel 1Release the lock button

2Press (Control panel is lit.)

●The count display lamp and “UP” or “DOWN” are illuminated.

Setting the count functions (Screw count setting/Count system setting)

1.Press while the control panel is illuminated.

Each time is pressed, the screw count setting and count system set- ting switch flash.

●Screw count setting

→Count display lamp flashes.

●Count system setting

→“UP” or “DOWN” flashes.

2.Screw count setting

Set the number of screws with or

.

● The range can be set within 0 – 99. ● 0 is not counted.

- -

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model No EY7411 ImportanteIndex/Index/Indice DEL Work Area Safety Electrical SafetyPersonal Safety Power Tool Use and CareII. Specific SAFE­ TY Rules Battery Tool Use and CareService Important Safety Instructions Symbol MeaningIV. Assembly Operation  Clutch Handle Clutch Torque Setting Hexagonal Bit Chuck Attaching the bitsReference for Adjusting Torque  Control PanelScrew count function Starting the control panelTo change the screw count while in use  Battery Low Warning Lamp  Using the LED Light Clutch Lock Cover Attaching the cover Speed Selector Switch  Main Switch Lock Main Switch ON/OFF  Battery Pack EY9L10Battery Pack For Appropriate Use of Bat­ tery pack Battery Charger ChargingNi-Cd Battery Pack During charging, the charging lamp will be litMaintenance VI. AccessoriesVII. Specifications Main UnitRite Generales Sécurité de la zone de travailSécurité électrique Sécurité personnelleMaintenez les outils de coupe affûtés et propres Utilisation et soins de l’outil méca­ niqueUtilisation et soins de la batterie de l’outil Particulieres Instructions de sécurité impor­ tantesRéparation AvertissementNorme d’entrée Ampères IV. Assemblage Fonctionnement  Mandrin de mèche hexagonalFixation des mèches Remarque Panneau de commande Démarrage du panneau de commandeRéférences pour l’ajustement du couple de serrage Fonction de comptage des visAppuyez sur alors que le panneau de commande est allumé  Témoin d’avertissement de batterie basse  Couvercle du verrouillage de l’embrayagePour changer le compte des vis pendant l’utilisation Fixation du couvercle Utilisation de la lumière DEL  Fonction de verrouillage de la mèche Interrupteur principal ON/OFF Enlèvement du couvercleBatterie autonome  Commutateur du sélecteur de vitesse Batterie autonome EY9L10  Verrou de l’interrupteur prin­ cipalChargeur de batterie Recharge Batterie autonome Li­ionLongévité des batteries autonomes Recyclage de la batterie autonomeBatterie autonome Ni-Cd VI. Accessoires EntretienVII. Caracteristiques Techniques Unite PrincipaleDAD Generales Seguridad del lugar de trabajoSeguridad eléctrica Seguridad personalMantenga las herramientas de corte afiladas y limpias Uso y cuidados de herramientas eléctricasUso y cuidado de la herramienta a batería DAD Específicas III. Para EL CARGA­Instrucciones de seguridad im­ portantes ServicioIgual o mayor Pero me IV. Montaje Y Funcionamiento  Portador de broca hexagonal Mango de embrague Ajuste de torsión del em­ brague Nota Tablero de controles Referencia para el ajuste de torsiónFunción de cuenta de tornillos Inicio del tablero de controlesLos ajustes se activarán presionando Instalación de la cubierta  Luz de advertencia de batería baja Cubierta de bloqueo del embrague  Utilización de la luz LED  Función de bloqueo de broca Interruptor principal ON/OFF Desmontaje de la cubiertaBatería Para un uso adecuado de la batería Cargador de la batería Carga Reciclado de la bateríaPrecauciones comunes para las baterías Li­ión/Ni­Cd Batería de Li­iónBatería Ni-Cd Precaucion MantenimientoVI. Accesorios VII. Especificaciones Unidad PrincipalPanasonic Consumer Electronics Company
Top Page Image Contents