DeWalt DWFP12658 Accessories, HOT Weather Operation, Daily Maintenance Chart

Page 12

HOT WEATHER OPERATION

Tool should operate normally. However, keep tool out of direct sunlight as excessive heat can deteriorate bumpers, O-rings and other rubber parts resulting in increased maintenance.

MAINTENANCE

WARNING: Disconnect air line from tool, engage trigger lock and remove fasteners from magazine before making adjustments or personal injury may result.

DAILY MAINTENANCE CHART

ACTION	WHY	HOW
Lubricate tool with	Prevents failure	Insert drops into air fitting
5-7 drops of DeWALT	of o-rings	on end cap of tool
Pneumatic Tool Oil
Drain compressor tanks	Prevents accumulation	Open petcocks or other
and hoses daily	of moisture in	drain valves on compressor
	compressor and nailer	tanks. Allow any accumulated
		water to drain from hoses
Clean canister, feed	Permits smooth	Blow clean with compressor
piston area and contact	operation of magazine,	air. The use of oils, lubricants
trip mechanism.	reduces wear and	periodically or solvents is
	prevents jams.	not recommended as they
		tend to attract debris.
Before each use, check	Prevents jams, leaks	Tighten loose screws or other
to insure all screws,	and premature failure	fasteners using the appropriate
nuts and fasteners are	of tool parts.	hex wrench or screwdriver.
tight and undamaged.

CLEANING

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

REPAIRS

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a DeWALT factory service center, a DeWALT authorized service center or other qualified service personnel. Always use identical replacement parts. Refer to the Troubleshooting Guide at the end of this section.

ACCESSORIES

WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with this product.

12 - ENG

Image 12

Contents DWFP12658 Guide D’UTILISATION Manual DE InstruccionesImportant Safety Instructions For Pneumatic Tools Definitions Safety GuidelinesCompressor rated at over 200 psi. The tool operating Fig. E Fig. K Bump or Contact Actuation Trigger Mode Sequential Action Trigger ModeTo Avoid Double Fires Nail Specifications Tool PartsAssembly OperationTrigger AIR FittingLoading the Tool FIG Platform Position Nail LengthSingle Sequential actuation trigger mode To operate the tool in Single sequential actuation ModeActuating Tool Adjusting Depth FIG Shingle Guide Clearing a Jammed NailCold Weather Operation Maintenance AccessoriesDaily Maintenance Chart Cleaning RepairsThree Year Limited Warranty Troubleshooting Guide Tool SpecificationsSymptom Problems Solutions Compressor Connected Tools Number Mesures DE Sécurité Définitions ’outil actionné pourrait projeter des débris, de laNe jamais modifier ni altérer l’outil. fig Fig. J Mode DE Détente Actionnée PAR Coup OU PAR Contact Mode DE Détente À Action Séquentielle Pour Éviter LES Doubles DéclenchementsPièces DE L’OUTIL Spécifications Relatives AUX ClousAssemblage FonctionnementDétente Raccord D’AIRChargement DE L’OUTIL FIG Actionnement DE L’OUTIL Position de la plateforme Longueur du clouMode de déclenchement séquentiel simple de la gâchette Fig Mode de déclenchement sur contact par gâchetteActivation du mode déclenchement Fonctionnement Intermittent de l’outilRéglage DE LA Profondeur FIG GUIDE-BARDEAUDégagement DES Clous Coincés Solution Pourquoi Comment EntretienFonctionnement PAR Temps Froid Fonctionnement PAR Temps ChaudAccessoires Garantie Limitée DE Trois ANSNettoyage RéparationsRemplacement Gratuit DE Letiquiette Guide DE DépannageSymptôme Problème Solution Fiche Technique DE L’OUTILNombre D’OUTILS Raccordés AU Compresseur Pautas DE SEGURIDAD/DEFINICIONES Regule la Presión De aire. Utilice presión de aireCompatible Con las Indicaciones de la placa de la No utilice gases envasados para esta herramienta Revise la herramienta antes de usarla. No opere unaFig. J Modo DE Gatillo DE Tope Para Evitar LOS Dobles Disparos Modo DE Gatillo SecuencialSiempre Piezas DE LA Herramienta Especificaciones DE LOS ClavosEnsamblaje OperaciónGatillo Conector DE AireCarga DE LA Herramienta FIG Funcionamiento DE LA Herramienta Posición de la plataforma Longitud del clavoModo de Disparo por contacto Fig Cambiar el modo de disparoAjuste DE LA Profundidad FIG Guía DE GuijarrosExtracción DE UN Clavo Atascado Mantenimiento Operación EN Condiciones Climáticas FríasOperación EN Condiciones Climáticas Calurosas Cuadro DE Mantenimiento DiarioAccesorios LimpiezaReparaciones Garantía Limitada POR Tres Años Reemplazo DE LAS Etiquetas DE AdvertenciaGuía DE Detección DE Problemas Síntoma Problema SoluciónEspecificaciones DE LA Herramienta Compresseur Raccordés ’OUTILS Nombre No se recomiendaDewalt Industrial Tool Co East Joppa Road Towson, MD