DeWalt DWFP12658 instruction manual Loading the Tool FIG, Platform Position Nail Length

Page 8

a.Use DeWALT pneumatic tool oil or a non-detergent S.A.E. 20 weight oil. DO NOT use detergent oil or additives as they will damage O-rings and rubber parts.

b.Use a filter when possible.

c.Add 5 to 7 drops of oil in the air fitting a least twice a day.

3.Wear eye and ear protection.

4.Ensure canister is empty of all fasteners.

5.Check for smooth and proper operation of contact trip. Do not use tool if assembly is not functioning properly. NEVER tamper with the contact trip. NEVER use a tool that has the contact trip restrained in the actuated position.

6.Adjust air supply: Ensure air pressure does not exceed recommended operating limits; 70 to 120 psi, (4.9 to 8.3 bar, 5 to 8.5 kg/cm2).

7.Keep tool pointed away from yourself and others.

8.Connect air hose.

9.Check for audible leaks around valves and gaskets. Never use a tool that leaks or has damaged parts.

WARNING: To reduce the risk of personal injury, disconnect tool from air supply and engage trigger lock before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location or handing the tool to another person.

LOADING THE TOOL (FIG. 1–6)

WARNING: Keep the tool pointed away from yourself and others. Serious personal injury may result.

WARNING: Never load nails with the contact trip or trigger activated. Personal injury

may result.

1.Read all Safety Warnings before using tool.

2.Connect the air supply to the tool.

3.Lift the canister door latch (E) to open the nail guide door (H).

4.Rotate the canister door (I) open.

5.Adjust the nail platform (J) to properly accommodate the nail length being used. Pull the nail platform (J) up or down for desired nail.

Fig. 2

E

HI

Platform Position	Nail Length
lowest position	1-1/2" (38 mm) - 1 3/4" (44.5mm)
center position	1-1/4" (32 mm)
upper position	3/4" (19 mm) - 1" (25 mm)

NOTE: 3/4" (19 mm) nails are not available for this tool.

6.Place the coil on the nail platform (J). NOTE: Observe fastener icon (K) Fig. 4. Insert

fasteners (L) with points down. IMPORTANT: Fasteners must point in the same direction as they will be driven.

7.Uncoil enough nails [approximately 3" (76 mm)] to reach the nose of the tool.

8.Insert the first nail into the nose and the second nail (M) between the two rails of the feed pawl as shown in Fig. 5.

8 - ENG

Image 8

Contents DWFP12658 Guide D’UTILISATION Manual DE InstruccionesCompressor rated at over 200 psi. The tool operating Important Safety Instructions For Pneumatic ToolsDefinitions Safety Guidelines Fig. E Fig. K To Avoid Double Fires Bump or Contact Actuation Trigger ModeSequential Action Trigger Mode Nail Specifications Tool PartsAssembly OperationTrigger AIR FittingLoading the Tool FIG Platform Position Nail LengthActuating Tool Single Sequential actuation trigger modeTo operate the tool in Single sequential actuation Mode Adjusting Depth FIG Cold Weather Operation Shingle GuideClearing a Jammed Nail Maintenance AccessoriesDaily Maintenance Chart Cleaning RepairsThree Year Limited Warranty Symptom Problems Solutions Troubleshooting GuideTool Specifications Compressor Connected Tools Number Mesures DE Sécurité Définitions ’outil actionné pourrait projeter des débris, de laNe jamais modifier ni altérer l’outil. fig Fig. J Mode DE Détente Actionnée PAR Coup OU PAR Contact Mode DE Détente À Action Séquentielle Pour Éviter LES Doubles DéclenchementsPièces DE L’OUTIL Spécifications Relatives AUX ClousAssemblage FonctionnementDétente Raccord D’AIRChargement DE L’OUTIL FIG Actionnement DE L’OUTIL Position de la plateforme Longueur du clouMode de déclenchement séquentiel simple de la gâchette Fig Mode de déclenchement sur contact par gâchetteActivation du mode déclenchement Fonctionnement Intermittent de l’outilDégagement DES Clous Coincés Réglage DE LA Profondeur FIGGUIDE-BARDEAU Solution Pourquoi Comment EntretienFonctionnement PAR Temps Froid Fonctionnement PAR Temps ChaudAccessoires Garantie Limitée DE Trois ANSNettoyage RéparationsRemplacement Gratuit DE Letiquiette Guide DE DépannageSymptôme Problème Solution Fiche Technique DE L’OUTILNombre D’OUTILS Raccordés AU Compresseur Compatible Con las Indicaciones de la placa de la Pautas DE SEGURIDAD/DEFINICIONESRegule la Presión De aire. Utilice presión de aire No utilice gases envasados para esta herramienta Revise la herramienta antes de usarla. No opere unaFig. J Modo DE Gatillo DE Tope Siempre Para Evitar LOS Dobles DisparosModo DE Gatillo Secuencial Piezas DE LA Herramienta Especificaciones DE LOS ClavosEnsamblaje OperaciónGatillo Conector DE AireCarga DE LA Herramienta FIG Funcionamiento DE LA Herramienta Posición de la plataforma Longitud del clavoModo de Disparo por contacto Fig Cambiar el modo de disparoExtracción DE UN Clavo Atascado Ajuste DE LA Profundidad FIGGuía DE Guijarros Mantenimiento Operación EN Condiciones Climáticas FríasOperación EN Condiciones Climáticas Calurosas Cuadro DE Mantenimiento DiarioReparaciones AccesoriosLimpieza Garantía Limitada POR Tres Años Reemplazo DE LAS Etiquetas DE AdvertenciaEspecificaciones DE LA Herramienta Guía DE Detección DE ProblemasSíntoma Problema Solución Compresseur Raccordés ’OUTILS Nombre No se recomiendaDewalt Industrial Tool Co East Joppa Road Towson, MD