DeWalt DWFP12658 instruction manual Adjusting Depth FIG

Page 10

Contact actuation trigger mode - (Fig. 8)

The contact actuation trigger is intended for rapid fastening on flat, stationary surfaces.

Using the contact actuation trigger mode, two methods are available: place actuation and contact actuation.

To operate the tool using the PLACE ACTUATION method:

1.Depress the contact trip against the work surface.

2.Pull the trigger to drive the fastener.

3.Allow the tool to recoil off the work surface

Trigger lock button

Fig. 8

C

To operate the tool using the CONTACT

Trigger mode selector button

ACTUATION method:

 

1.Pull the trigger.

2.Depress the contact trip against the work surface. As long as the trigger is pulled, the tool will drive a fastener every time the contact trip is depressed. This allows the user to rapidly drive multiple fastener in sequence.

Changing the Actuation Mode -

WARNING: To reduce risk of serious injury, disconnect tool from air supply before changing actuation mode.

1.Push the (black) trigger lock button down

2.Rotate the (black) selectable trigger button counterclockwise

3.Align the triangular indicator to the desired mode

For Sequential Mode

For Contact Mode

4.Then push the trigger lock button back up to the un-locked position.

ADJUSTING DEPTH (FIG. 9)

WARNING: To reduce risk of serious injury from accidental actuation when attempting to adjust depth,

ALWAYS:

Disconnect air supply and engage trigger lock.

Avoid contact with trigger during adjustments.

The depth that the fastener is driven can be adjusted using the depth adjustment next to the trigger of the tool. The depth of drive is factory adjusted to a nominal setting. Test fire a fastener and check depth. If a change is desired:

Fig. 9

G

1.To drive the nail shallower, rotate the depth setting wheel (G) to the right.

2.To drive a nail deeper, rotate the depth setting wheel (G) to the left.

The adjustment knob has detents every 1/4 turn. Test drive another fastener and check depth. Repeat as necessary to achieve desired results. The amount of air pressure required will vary depending on the size of the fastener and the material being fastened. Experiment with the air pressure setting to determine the lowest setting that will consistently perform the job at hand. Air pressure in excess of that required can cause premature wear and/or damage to the tool.

10 - ENG

Image 10
Contents DWFP12658 Guide D’UTILISATION Manual DE InstruccionesDefinitions Safety Guidelines Important Safety Instructions For Pneumatic ToolsCompressor rated at over 200 psi. The tool operating Fig. E Fig. K Sequential Action Trigger Mode Bump or Contact Actuation Trigger ModeTo Avoid Double Fires Nail Specifications Tool PartsTrigger AssemblyOperation AIR FittingLoading the Tool FIG Platform Position Nail LengthTo operate the tool in Single sequential actuation Mode Single Sequential actuation trigger modeActuating Tool Adjusting Depth FIG Clearing a Jammed Nail Shingle GuideCold Weather Operation Daily Maintenance Chart MaintenanceAccessories Cleaning RepairsThree Year Limited Warranty Tool Specifications Troubleshooting GuideSymptom Problems Solutions Compressor Connected Tools Number Mesures DE Sécurité Définitions ’outil actionné pourrait projeter des débris, de laNe jamais modifier ni altérer l’outil. fig Fig. J Mode DE Détente Actionnée PAR Coup OU PAR Contact Mode DE Détente À Action Séquentielle Pour Éviter LES Doubles DéclenchementsPièces DE L’OUTIL Spécifications Relatives AUX ClousDétente AssemblageFonctionnement Raccord D’AIRChargement DE L’OUTIL FIG Actionnement DE L’OUTIL Position de la plateforme Longueur du clouActivation du mode déclenchement Mode de déclenchement séquentiel simple de la gâchette FigMode de déclenchement sur contact par gâchette Fonctionnement Intermittent de l’outilGUIDE-BARDEAU Réglage DE LA Profondeur FIGDégagement DES Clous Coincés Fonctionnement PAR Temps Froid Solution Pourquoi CommentEntretien Fonctionnement PAR Temps ChaudNettoyage AccessoiresGarantie Limitée DE Trois ANS RéparationsRemplacement Gratuit DE Letiquiette Guide DE DépannageSymptôme Problème Solution Fiche Technique DE L’OUTILNombre D’OUTILS Raccordés AU Compresseur Regule la Presión De aire. Utilice presión de aire Pautas DE SEGURIDAD/DEFINICIONESCompatible Con las Indicaciones de la placa de la No utilice gases envasados para esta herramienta Revise la herramienta antes de usarla. No opere unaFig. J Modo DE Gatillo DE Tope Modo DE Gatillo Secuencial Para Evitar LOS Dobles DisparosSiempre Piezas DE LA Herramienta Especificaciones DE LOS ClavosGatillo EnsamblajeOperación Conector DE AireCarga DE LA Herramienta FIG Funcionamiento DE LA Herramienta Posición de la plataforma Longitud del clavoModo de Disparo por contacto Fig Cambiar el modo de disparoGuía DE Guijarros Ajuste DE LA Profundidad FIGExtracción DE UN Clavo Atascado Operación EN Condiciones Climáticas Calurosas MantenimientoOperación EN Condiciones Climáticas Frías Cuadro DE Mantenimiento DiarioLimpieza AccesoriosReparaciones Garantía Limitada POR Tres Años Reemplazo DE LAS Etiquetas DE AdvertenciaSíntoma Problema Solución Guía DE Detección DE ProblemasEspecificaciones DE LA Herramienta Compresseur Raccordés ’OUTILS Nombre No se recomiendaDewalt Industrial Tool Co East Joppa Road Towson, MD